background image

 

Area of Rescue Command Unit

 

Installation Guide 

Model AOR-5 / Model AOR-10

 

Page 

19

 of 

23

 

 

  Rev. 4/13/2022

 

 

Copyright 2022 Talk-A-Phone, LLC

 

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.  

 

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, bAlert, Scream Alert, WEBS, and WEBS Contact are registered trademarks of 
Talk-A-Phone, LLC.  All rights reserved.  All other trademarks mentioned in this document or website are the property of their respective owners and does not imply or indicate 
any approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated. 

3. 

Answering Calls at the Command Unit 

1.  When calls are routed to the Command Unit handset, the Command Unit will ring. 

2.  To answer the call, pick up the Command Unit handset. 

3.  A prerecorded voice message with physical location information may play at the 

beginning of the call. 

4. 

Answering Calls at a Sub-Command Unit 

1.  When calls are routed to a Sub-Command Unit, the Sub-Command Unit will ring. 

2.  To answer the call, pick up the Sub-Command Unit handset. 

3.  A prerecorded voice message with physical location information may play at the 

beginning of the call. 

5. 

Answering Calls Off-site or at a Central Station 

When calls are routed off-site (i.e. monitoring service, call center, central station, or 911), calls 
are answered accordingly and a prerecorded voice message with physical location information 
may play at the beginning of the call. 
 

6. 

All Call to AOR-CSE Stations 

From either Sub-Command Unit or through a remote PSTN call, enter 

* 4 # *

.  This command 

will call every AOR-CSE Station and initiate a one-way audio page. 
 
An all call initiated through a remote PSTN call has a 90 second limit. 
 
An all call initiated through a Sub-Command unit does not have a time limit. 
 
This operation command does 

not

 require initial entry of the Guard Access Code or the Master 

Access Code. 

 

 

Содержание AOR-10
























Отзывы: