manualshive.com logo in svg

Talgil DREAM 2, Руководство по установке, Страница: 41 / 61

Поделиться
Скачать
Talgil DREAM 2 Скачать руководство пользователя страница 41

41

 

 

 
 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 

 

When the system contains water sources each water source will have a definition of the number 

of outputs (usually water pumps) belonging to the water source and whether or not a water 

meter is included in the water source. 

 

 
 
 
 
 
 
 
 
 
 

The next step will be the definition of the irrigation lines contents including the following 

information: 

 

 

How many valves are included in each line? 

 

Does the irrigation line contain local fertilizer site? 

 

Is the irrigation line connected to a central fertilizer site, if yes to which one?  

 

Does the irrigation line contain local filter site? 

 

Is the irrigation line connected to a central filter site, if yes to which one?   

 

Does the irrigation line contain a dry contact pressure sensor? If yes, it should be the 

normally open type.  

 
 
 

Water meters that not associated with 

irrigation lines  

Source A has 2 pumps and source B has 1 

pump 

 

The irrigation lines will automatically 

get the default structure as defined 

here. Later on each line can be 

adjusted as required. 

Source A has no water meter but 

source

 B does 

 

In our example there are two contacts C1 

and C2 used as level sensors of source “A”  

Analog inputs supply a whole range of 

values presented as 4-20 mA or 0-5 v. Not 

implemented in our example 

When Fert. agitation is defined there will be 

an additional output added to each fertilizer 
injector for agitating the fertilizers. 

When flow switches are added per valve 

they will indicate whether the valve really 

executed the Open/Close commands. 

Содержание DREAM 2






























































Отзывы:

Нет отзывов