Talgil DREAM 2 страница 22 Скачать руководство пользователя

Страница: 22 / 61

Restoring the configuration from USB

–

will restore the configuration

of the controller from the backup file stored on the USB memory stick.

Recovering configuration from internal backup

–

Loading the

configuration from the internal backup saved inside the controllers memory

each midnight.

VPN ON/OFF switch

– this is the place where the

irtual

rivate

etwork can be

activated. The VPN acts like a bypass to the regular communication channel, which

is used by the technicians in case of need. Activating the VPN should only be done

by request from the technical team of Talgil.

4.6

Modem

This subject deals with the definitions required for cellular modem communication. It can

be accessed only when the

Modem

communication was selected (

see 4.1 above

The system recognizes several models of modems for which the appropriate drivers are

available. So first thing is to select the type of modem we intend to use.

After selecting the type of modem in use, the

APN

should be defined.

The

APN

is the

ccess

oint

ame used by the specific cellular data communication

provider. Wrong

APN

may block the data communication.

The user name, the password and the dialing number are usually ignored. The local

service provider should be consulted about these parameters.

The last two rows supply information about the modem status and about the signal level.

When the modem fails to connect for a long time (more than 5 minutes) the user may

push

F3=Connect

, this will reset the modem and force it to try again.

Sometimes the reason for connection failure is the SIM card which is defected or

misplaced; it is worth trying another SIM card or check with the provider about the

features included in the specific SIM card.

The selected
modem model

APN of the
provider

Содержание DREAM 2






























































Результаты поиска

Содержание DREAM 2

Отзывы:

Похожие инструкции для DREAM 2

Бренды по названию

Популярные бренды

Talgil DREAM 2, Руководство по установке

Результаты поиска

Содержание DREAM 2

Отзывы:

Похожие инструкции для DREAM 2

Бренды по названию

Популярные бренды