⑤
1. Loosen the cover locking screw
and remove the cover unit.
2. Insert the wire through the grommet in the wiring
hole at the bottom of the sensor unit. Break the
mounting hole knockout of the sensor unit and
mount using the supplied tapping screws.
When mounting on the pole
[Use the pole attachment]
When mounting on the ceiling or under eaves
[Use the ceiling attachment]
When mounting the unit on a vertical pole, use the pole attachment
(sold separately). The unit can be mounted on poles of
φ
38 to
φ
45mm
(Dia 1.5
µ
to 1.8
µ
) and
φ
40 to
φ
140mm
(Dia 1.6
µ
to 5.5
µ
).
* Mount the sensor so that its mounting surface is positioned vertically.
When mounting on the ceiling or under eaves,
use the ceiling attachment (sold separately).
* Mount the sensor so that its mounting
surface is positioned vertically.
The mounting height and adjustable detection distance depend on the operation mode. Carefully check the operation mode and
detection area setting before installation and area setting.
* When the unit operates with anti-masking
function ON, mount it at least 30cm (1ft.)
away from any adjoining wall / surface to
avoid unexpected reflection.
3ROH
DWWDFKPHQW
%3
3ROHGLDPHWHU
Ѯ
WRPP
'LDµWRµ
3ROH
DWWDFKPHQW
%3
3ROHGLDPHWHU
Ѯ
WRPP
'LDµWRµ
■
Mounting method
When using the pole
attachment BP-32 (sold
separately), break the
knockout on the rear
side of the sensor unit,
and attach it.
* Adjust mounting height of the sensor using the
center of the sensor unit as a guide.
Use the unit with the correct operation mode setting. Select operation mode to use and perform the setting correctly.
This unit can be operated from
①
to
④
modes, as follows.
Insert the wires for power input and alarm
output through the wiring hole on the left,
and for tamper output and starting output on
the right. Be careful not to cross the wires.
,167$//$7,21
Pole
attachment
BP-32
Ceiling
attachment
KP-32
Pole
attachment
BP-32
FP
IW
* For open wiring, break the knockout on the rear
side of the sensor unit, and pull the wire
through it.
3. Connect the wires to each terminal.
(Refer to “6 WIRING”)
4. Set the detection area and functions according to
the installation site.
(Refer to “4 DETECTION AREA”, “7 FUNCTION”,
and “8 ADJUSTMENT OF DETECTION”)
5. Replace the cover unit,
and fix it by
tightening the cover
locking screws.
* When installing
outdoors, mount the
anti bird spike above
the cover unit. Turn
the anti bird spike and
tighten it.
6. When the detection area and functions settings
are completed, go to section “9 OPERATION
CHECK”.
●
Normal operation modes
●
Specialized operation mode
7KLVLVRSHUDWLRQVHWWLQJWRH[WUHPHO\UHGXFHWKHORVWGHWHFWLRQLQGHWHFWLRQDUHD
④
+LJKGHQVLW\PRGH
0RXQWLQJKHLJKWLVWRPWR
7KHPRGHVHWWLQJFDQEHVHOHFWHGIURPDERYH
①〜④
PRGHV5HIHUWR)81&7,21
Operation mode
Low position mode
Middle position mode
High position mode
High density mode
Installation height
2.0 to 2.5m (6.6 to 8.3 )
2.5 to 3.5m (8.3 to 11.5 )
3.5 to 4.0m (11.5 to 13 )
2.0 to 6.0m (6.6 to 20 )
Detection distance
40ｍ (135 )
35ｍ (115 )
30ｍ (100 )
45ｍ (150 )
1RUPDORSHUDWLRQPRGHUHGXFHVWKHIDOVHGHWHFWLRQFDXVHGE\VPDOODQLPDOV
DQGORVWGHWHFWLRQRIKXPDQV7KHUHDUHWKUHHSRVLWLRQPRGHVDFFRUGLQJWR
PRXQWLQJKHLJKW/RZ0LLJK
①
/RZSRVLWLRQPRGH
:KHQWKHVHQVRULVPRXQWHGEHWZHHQDKHLJKWRIWRPWR
②
0LGGOHSRVLWLRQPRGH
:KHQWKHVHQVRULVPRXQWHGEHWZHHQDKHLJKWRIWRPWR
③
+LJKSRVLWLRQPRGH
:KHQWKHVHQVRULVPRXQWHGEHWZHHQDKHLJKWRIWRPWR
:KHQWKHPRXQWLQJKHLJKWLVP/RZRU0LGGOHSRVLWLRQLVVHOHFWDEOH
:KHQWKHPRXQWLQJKHLJKWLVP0LJKSRVLWLRQLVVHOHFWDEOH
:LULQJ
3RZHU$ODUP
:LULQJ
7DPSHU([WHUQDO
&HQWHURI
WKHVHQVRU
,QVWDOODWLRQKHLJKW
