Takeuchi TB108 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 170

background image

1

It is your responsibility to observe all pertinent laws and regulations and to follow the
manufacturer’s instructions on machine operation, inspection and maintenance.

Virtually all accidents occur as the result of a failure to observe basic safety rules and
precautions. An accident can often be avoided by recognizing potentially hazardous situations
beforehand. Read and understand all of the safety messages which explain how to prevent
these accidents from occurring. Do not operate the machine until you are sure that you have
gained a proper understanding of its operation, inspection and maintenance.

■

SlGNAL WORDS

Safety messages appearing in this manual and on machine decals are identified by the
words “DANGER”, “WARNING” and “CAUTION”. These signal words mean the following:

The word “DANGER”
indicates an imminently
hazardous situation
which, if not avoided,
can result in serious
injury or death.

The word “WARNING”
indicates a potentially
hazardous situation
which, if not avoided,
could result in serious
injury or death.

The word “CAUTlON”
indicates a potentially
hazardous situation
which, if not avoided,
may result in minor or
moderate injury.

DANGER

WARNING

CAUTION

IMPORTANT: The word “IMPORTANT” is used to alert against operators and
maintenance personnel about situations which can result in possible damage to the
machine and its components.

It is impossible to foresee every possible circumstance that might involve a potential hazard.
The warnings in this manual or on the machine can not cover all possible contingencies. You
must exercise all due care and follow normal safety procedures when operating the machine
so as to ensure that no damage occurs to the machine, its operators or other persons.

■

EXPLANATION OF GRAPHICAL SYMBOLS

Following is an explanation of symbols used in this manual.

/ X ......... prohibition

........... Lock

......... Unlock

«
1
2
3
4
5
...
»

Содержание TB108











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB108

Бренд: Case Страницы: 61

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 41

Бренд: Daewoo Страницы: 16

Бренд: jcb Страницы: 4

Бренд: jcb Страницы: 51

Бренд: IHI Страницы: 110

Бренд: LSM Страницы: 44

Бренд: Komatsu Страницы: 248

MAGNUM SIGNATURE SERIES

Бренд: Norfield Страницы: 6

Бренд: disperator Страницы: 36

Бренд: CNH Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды