background image

10  

GAS SUPPLY AND GAS PIPE SIZING 

Check  that  the  type  of  gas  matches  the  rating 

plate located on the cover of your water heater. 

The  minimum  and  maximum  inlet  gas  pressures 

are:

Natural Gas  Min. 5.5” WC - Max. 10.5” WC

Propane Gas  Min. 9.5” WC - Max. 14” WC 

Gas  pressure  below  this  specified  range  for  the 

T-KJR  and/or  insufficient  gas  volume  will 

adversely affect performance.  Inlet gas pressure 

must not exceed the above maximum values; gas 

pressure  above  the  specified  range  will  cause 

dangerous  operating  conditions  and  damage  to 

the unit. Until testing of the main gas line supply 

pressure is completed, ensure the gas line to the 

T-KJR  is  disconnected  to  avoid  any  damage  to 

the water heater. 

Size  the  gas  pipe  appropriately  to  supply  the 

necessary volume of gas required for the T-KJR 

(140,000  BTUH)  using  ANSI233.1/NAPA  54  in 

the USA or CAN/CSA B149.1 in Canada or local 

codes.  Install  a  manual  gas  shut-off  valve 

between  the  T-KJR  and  the  gas  supply  line.   

When  the  gas  connections  are  completed,  it  is 

necessary  to  perform  a  gas  leak  test  either  by 

applying  soapy  water  to  all  gas  fittings  and 

observing  for  bubbles  or  by  using  a  gas  leak 

detection  device.    Always  purge  the  gas  line  of 

any  debris  before  connecting  to  the  heater  gas 

inlet.

Pipe  Sizing  Example:

  This  table  below  is  for 

Natural  gas  piping  supply  straight  to  the  water 

heater without any tabs to other gas appliances 

Recommend Gas pipe size for 

T-KJR Water Heater(Example for NG)

Distance from Gas Meter  Pipe Size (inches) 

0' - 60' 

3/4" 

60' - 150' 

1" 

150' – 300’ 

1-1/4" 

1.  Turn  off  all  electric  power  to  the 

water  heater  if  service  is  to  be 

performed.

2.  Turn the manual gas valve located 

on the outside of the unit clockwise 

 to the off position. 

A.  This water heater does not have a 

pilot.    It  is  equipped  with  an 

electronic  ignition  device  that 

automatically lights the burner.  Do 

not try to light the burner manually;

B.  BEFORE  OPERATING,  check  all 

around  the  water  heater  area  for 

gas  leaks.    Be  sure  to  check  next 

to  the  floor  as  some  gases  are 

heavier  than  air  and  will  settle  on 

the floor; 

C.  Use only your hand to turn the gas 

valve knob. Never use tools. If the 

knob  will  not  turn  by  hand,  do  not 

attempt to repair it. Call a qualified 

service  technician.  Force  or 

attempted repair may result in a fire 

or explosion. 

D.

WARNING:

 Conversion of this unit 

from  natural  gas  to  propane  or 

propane  to  natural  gas  cannot  be 

done in the field. Contact your local 

distributor to get the correct unit for 

your gas type. Conversion done by 

anyone 

other 

than 

the 

manufacturer will void all warranty

.

TO TURN OFF GAS TO  

APPLIANCE

FOR YOUR SAFETY, READ 

BEFORE OPERATING: 

Содержание Flash Water Heater T-KJr





























Отзывы: