Takagi 110c Скачать руководство пользователя страница 17

Страница: 17 / 52

Page

-Clearances for sidewall terminations-

-Clearances for rooftop terminations-

Multiple-unit, concentric wall

terminals: Space each concentric

wall terminal at least 1 ft (30 cm)

away from each other, no matter

the orientation. A concentric wall

terminal must also be at least 2 ft

(61 cm) away from an inside corner.

If the adjacent wall is less than 2

ft (61 cm) of length, the minimum

required distance away from the

inside corner will be equal to the

length of that adjacent wall.

Concentric wall terminals

should be at least 2 ft (61

cm) away from an opposite

surface/wall. Do not place the

termination directly in front of

an opening into a building.

Concentric wall
terminals should be at
least 3 ft (91 cm) away
from a ventilated or
unventilated soffit.

Installation

Installation Manual

Inside

corner

Anticipa

ted sno

w level

1 ft

(30 cm)

min.

2 ft

(61 cm)

min.

1 ft (30 cm)

min.

2 ft

(61 cm)

min.

3 ft

(91 cm)

min.

Improper installation can result in carbon monoxide poisoning or death. Follow all local

and national codes in regards to proper termination clearances. In the absence of such

codes, the clearances below can be used as guidelines. Local codes supersede these

guidelines.

WARNING

Canadian requirements differ from the guidelines in this section. In Canada, follow

the requirements of B149.1 (Natural Gas and Propane Installation Code, current

edition) as well as local and provincial codes. Contact your local code enforcement

agency for direction.

NOTICE

Angled roof termination

Intake air

Exhaust

gas

Exhaust

gas

5 ft (152 cm) min.

1 ft

(30 cm)

min.

1 ft

(30 cm)

min.

Anticipa

ted

sno

w le

vel

Flat roof termination

Intake air

Exhaust

gas

Exhaust

gas

2 ft (61 cm)

min.

1 ft

(30 cm)

min.

Anticipated

snow level

2 ft (61 cm) min.

1 ft

(30 cm)

min.

Vertical

wall

•

Minimum spacing between multiple concentric terminals for rooftop:

•

On the same level: 2 ft (61 cm) spacing between each

•

On the different level: 5 ft (152 cm) spacing between each

•

The exhaust termination must be a horizontal distance of at least 2 ft (61 cm) from a wall

or surface unless specified differently by local code.

•

Failure to observe this warning may result in severe personal injury or death.

WARNING

1 ft

(30 cm)

min.

Содержание 110c





















































Результаты поиска

Содержание 110c

Отзывы:

Похожие инструкции для 110c

Бренды по названию

Популярные бренды

Takagi 110c, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 110c

Отзывы:

Похожие инструкции для 110c

Бренды по названию

Популярные бренды