Tadano GR-800XL, Руководство пользователя

Страница: 15 / 16

GR-800XL RATED LIFTING CAPACITIES (IN POUNDS)
ON RUBBER
A Stationary Creep
Over Front
360
o
Rotation
Over Front
39.4' 68.1' 96.8' 39.4' 68.1' 96.8' 39.4' 68.1' 96.8'
B C (12m) C (20.8m) C (29.5m) C (12m) C (20.8m) C (29.5m) C (12m) C (20.8m) C (29.5m)
12'
66
60,000
66
38,000
66
45,000
15'
61
49,600
61
28,500
61
36,600
20'
52
37,500
70
35,000
52
17,500
70 52
26,800
70
29,200
25'
41
28,500
65
29,500
74
22,900
40
10,400
65 73
14,000
40
20,500
65
22,800
74
22,900
30'
25
21,500
60
24,000
71
21,500
25
6,500
60 70
10,000
25
15,600
60
18,200
71
18,900
35'
55
19,200
67
19,500
55 67
7,400
55
14,800
67
15,500
40'
49
15,200
64
16,000
49 63
5,400
49
12,000
64
12,900
45'
43
12,200
60
13,000
43 60
3,900
43
9,800
60
10,600
50'
36
9,700
57
10,600
36 56
2,700
36
7,900
57
8,900
55'
27
8,000
53
8,800
53
1,700
27
6,500
53
7,300
60'
13
6,500
49
7,400
13
5,200
49
6,100
65'
45
6,100
44
5,000
70'
40
5,000
40
4,100
75'
35
4,100
34
3,200
80'
28
3,400
28
2,500
85'
20
2,700
D 0 0 28 45 0
Telescoping conditions (%)
Tele.
mode
I, II II II I, II II II I, II II II
2nd boom
0 0 0 0 0 0 0 0 0
3rd boom
0 33 66 0 33 66 0 33 66
4th boom
0 33 66 0 33 66 0 33 66
Top boom
0 33 66 0 33 66 0 33 66
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON RUBBER OPERATION
A
Stationary Creep
Over Front
360
o
Rotation
Over Front
39.4' 68.1' 96.8' 39.4' 39.4' 68.1' 96.8'
C B
(12m)
B
(20.8m)
B
(29.5m)
B
(12m)
B
(12m)
B
(20.8m)
B
(29.5m)
0
32.2'
19,300
60.8'
6,300
89.1'
2,100
32.2'
5,100
32.2'
14,100
60.8'
5,000
89.1'
1,400
A :Boom length in feet
B :Load radius in feet
C :Loaded boom angle (
o
)
D :Minimum boom angle (
o
) for indicated length (no load)
NOTE: The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based
on the standard number of parts of line listed in the chart.
Standard number of parts of line for rubber operation should be according to the
following table.
Boom length in feet 39.4' 39.4' to 96.8' Single top
(meters) (12m) (12m to 29.5m) Jib
Number of parts of line 6 4 1
WARNING AND OPERATING INSTRUCTIONS
FOR ON RUBBER LIFTING CAPACITIES
1. Rated lifting capacities on rubber are in pounds and do not exceed 6. Over front operation shall be performed within two degrees in front of
75 % of tipping loads as determined by SAE J765-Crane Stability chassis.
Test Code. 7. On rubber lifting with "jib" is not permitted. Maximum permissible
2. Rated lifting capacities shown in the chart are based on condition boom length is 96.8 ft. (29.5m).
that crane is set on firm level surfaces with axle oscillation lockout 8. When making lift on rubber stationary, set parking brake.
applied. Those above bold lines are based on tire capacity and 9. For creep operation, boom must be centered over front of machine,
those below, on crane stability. They are based on actual load slewing lock engaged, and load restrained from slewing. Travel slowly
radius increased by tire deformation and boom deflection. and keep the lifted load as close to the ground as possible, and
3. If the axle oscillation lockout cylinders contain air, the axle will not especially avoid any abrupt steering, accelerating or braking.
be locked completely and rated lifting capacities may not be 10. Do not operate the crane while carrying the load.
obtainable. Bleed the cylinders according to the operation safety 11. Creep is motion for crane not to travel more than 200' (60 m) in any
and maintenance manual. 30 minute period and to travel at the speed of less than 1 mph
4. Rated lifting capacities are based on proper tire inflation, capacity (1.6km/h).
and condition. Damaged tires are hazardous to safe operation of 12. For creep operation, choose the drive mode and proper gear
crane. according to the road or working condition.
5. Tires shall be inflated to correct air pressure.
Tires Air Pressure
29.5-25 34PR 57 psi (400kPa)
1,800
20,000
14,000
9,500
6,500
4,500
3,000
15