Tadano GR-550XL, Руководство пользователя

Страница: 11 / 12

GR-550XL RATED LIFTING CAPACITIES (IN POUNDS)
ON RUBBER
A Stationary Creep
Over Front
360
o
Rotation
Over Front
35.1' 61.4' 87.6' 35.1' 61.4' 87.6' 35.1' 61.4' 87.6'
B C (10.7m) C (18.7m) C (26.7m) C (10.7m) C (18.7m) C (26.7m) C (10.7m) C (18.7m) C (26.7m)
10' 66 48,300 66 27,200 66 35,600
12' 62 41,800 62 22,500 62 30,500
15'
56
34,300
72
30,500
56
16,300
72 56
24,700
72
26,000
20'
45
26,000
67
23,300
45
9,200
67 45
18,300
67
19,400
25' 29 18,100 62 18,300 71 13,400 30 5,500 62 71 7,500 29 13,900 62 15,200 71 13,400
30'
56
13,900
68
11,000
56 68
5,000
56
12,100
68
11,000
35' 50 10,700 64 9,200 50 64 3,500 50 9,600 64 9,200
40' 43 8,300 60 7,900 43 60 2,200 43 7,700 60 7,900
45'
35
6,500
57
6,900
35 56
1,400
35
6,200
57
6,900
50' 25 5,100 52 5,500 25 5,100 52 5,500
55'
48
4,400
48
4,400
60' 43 3,600 43 3,600
65'
38
2,800
38
2,800
70' 31 2,200 31 2,200
75'
23
1,700
23
1,700
80' 9 1,300 9 1,300
D 0 0 28 53 0
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON RUBBER OPERATION
A Stationary Creep
Over Front
360
o
Rotation
Over Front
35.1' 61.4' 87.6' 35.1' 35.1' 61.4' 87.6'
C B (10.7m) B (18.7m) B (26.7m) C (10.7m) B (10.7m) B (18.7m) B (26.7m)
0
27.8'
15,500
54.1'
4,100
80.2'
1,190
27.8'
4,050
27.8'
12,000
54.1'
4,100
80.2'
1,190
A :Boom length in feet
B :Load radius in feet
C :Loaded boom angle (
o
)
D :Minimum boom angle (
o
) for indicated length (no load)
NOTE: The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based
on the standard number of parts of line listed in the chart.
Standard number of parts of line for rubber operation should be according to the
following table.
Boom length in feet 35.1' 35.1' to 87.6' Single top
(meters) (10.7m)
(10.7m to 26.7m)
Jib
Number of parts of line 6 4 1
WARNING AND OPERATING INSTRUCTIONS
FOR ON RUBBER LIFTING CAPACITIES
1. Rated lifting capacities on rubber are in pounds and do not exceed 6. Over front operation shall be performed within two degrees in front of
75 % of tipping loads as determined by SAE J765-Crane Stability chassis.
Test Code. 7. On rubber lifting with "jib" is not permitted. Maximum permissible
2. Rated lifting capacities shown in the chart are based on condition boom length is 87.6' (26.7m).
that crane is set on firm level surfaces with axle oscillation lockout 8. When making lift on rubber stationary, set parking brake.
applied. Those above bold lines are based on tire capacity and 9. For creep operation, boom must be centered over front of machine,
those below, on crane stability. They are based on actual load swing lock engaged, and load restrained from swinging. Travel slowly
radius increased by tire deformation and boom deflection. and keep the lifted load as close to the ground as possible, and
3. If the axle oscillation lockout cylinders contain air, the axle will not especially avoid any abrupt steering, accelerating or braking.
be locked completely and rated lifting capacities may not be 10. Do not operate the crane while carrying the load.
obtainable. Bleed the cylinders according to the operation safety 11. Creep is motion for crane not to travel more than 200' (60 m) in any
and maintenance manual. 30 minute period and to travel at the speed of less than 1 mph
4. Rated lifting capacities are based on proper tire inflation, capacity (1.6km/h).
and condition. Damaged tires are hazardous to safe operation of 12. For creep operation, choose the drive mode and proper gear
crane. according to the road or working condition.
5. Tires shall be inflated to correct air pressure.
Tires Air Pressure
23.5-25 65 psi (450 kPa)
2,900
1,800
1,000
16,300
10,700
6,800
4,600
11