CRANE SPECIFICATIONS
CARRIER SPECIFICATIONS
TADANO Automatic Moment Limiter (AML-E2) including:
• Control lever lockout function with audible and visual
pre-warning
• Number of parts of line
• Boom position indicator
• Outrigger state indicator
• Slewing angle
• Boom angle / boom length / jib offset angle / jib length / load
radius / rated lifting capacities / actual loads read out
• Potential lifting height
• Ratio of actual load moment to rated load moment indication
• Permissible load
• Automatic Speed Reduction and Slow Stop function on
boom elevation and slewing
• Working condition register switch
• Load radius / boom angle / tip height / slewing range preset
function
• External warning lamp
• Tare function
• Main hydraulic oil pressure
• Fuel consumption monitor
• Main winch / auxiliarly winch select
• Drum rotation indicator (visible type) main and auxiliary
winch
• On-rubber indicator
TADANO AML-E2 monitors outrigger extended length and
automatically programs the corresponding "RATED LIFTING
CAPACITIES" table
Operator's right hand console includes transmission gear selector,
slewing lock lever and sight level bubble.
Upper right console includes roof washer and wiper switch,
emergency outrigger set up key switch, jib status switch, high
speed winch (main / aux) switch, cab tilt switch, automatic pump
disconnect enable switch, boom emergency telescoping switch
(2nd and 3rd-top)
NOTE: Each crane motion speed is based on unladen conditions.
TYPE
Rear engine, left-hand drive, driving axle 2-way selected type
by manual switch, 4x2 front drive, 4x4 front and rear drive.
FRAME
High tensile steel, all welded mono-box construction.
ENGINE
Model
Type
No. of cylinders
Combustion
Bore x Stroke, mm
Displacement, liters
Air inlet heater
Air cleaner
Oil filter
Fuel filter
Fuel tank, liters
Cooling
Radiator
Fan, mm
Starting
Charging
Battery
Compressor, air, l /min
Output, Max. kW (HP)
Torque, Max. N
•
m
Capacity, liters
Cooling water
Lubrication
Fuel
TRANSMISSION
Electronically controlled full automatic transmission.
Torque converter driving full powershift with driving axle selector.
6 forward and 2 reverse speeds, constant mesh.
3 speeds - high range - 2-wheel drive; 4-wheel drive
3 speeds - low range - 4-wheel drive
TRAVEL SPEED
- 36 km/h
GRADE ABILITY (tan
θ
)
- 85% (at stall), 30%*
* Machine should be operated within the limit of engine crankcase
design (17˚: MITSUBISHI 6M60-TLU3R)
AXLE
Front: Full floating type, steering and driving axle with planetary
reduction.
Rear: Full floating type, steering and driving axle with planetary
reduction and non-spin rear differential.
STEERING
Hydraulic power steering controlled by steering wheel.
4 steering modes available: 2 wheel front, 2 wheel rear, 4 wheel
coordinated and 4 wheel crab.
SUSPENSION
Front: Rigid mounted to the frame.
Rear: Pivot mounted with hydraulic lockout device.
BRAKE SYSTEMS
Service: Air over hydraulic disc brakes on all 4 wheels.
Parking/Emergency: Spring applied-air released brake acting
on input shaft of front axle.
Auxiliary: Electro-pneumatic operated exhaust brake.
TIRES
- 29.5-25 36PR (OR) Air pressure: 470 kPa
29.5-25 40PR (OR) Air pressure: 465 kPa
OUTRIGGERS
4 hydraulic, beam and jack outriggers.
Vertical jack cylinders equipped with integral holding valve.
Each outrigger beam and jack is controlled independently from cab.
Beams extend to 7.3 m center-line and retract to within
3.315 m overall width with floats. Outrigger jack floats
are attached thus eliminating the need of manually attaching and
detaching them. Controls and sight bubble located in
superstructure cab. 4 outrigger extension lengths are provided with
corresponding "RATED LIFTING CAPACITIES" for crane duty in
confined areas.
Min. Extension
2.7 m center to center
Mid. Extension
5.5 m center to center
Mid. Extension
6.7 m center to center
Max. Extension
7.3 m center to center
Float size (Diameter) 0.6 m
MITSUBISHI 6M60-TLU3R
[ECE-R96-02]
Direct injection diesel
6
4 cycle, turbo charged and after cooled
118 x 115
7.54
24 volt preheat
Dry type, replaceable element
Full flow with replaceable element
Full flow with replaceable element
300, right side of carrier
Liquid pressurized, recirculating by-pass
Fin and tube core, thermostat controlled
Suction type, 6-blade, 600 dia.
24 volt
24 volt system, negative ground
2-120 amp. Hour
830 at 2,600 min
-1
Gross 200 (267) at 2,600 min
-1
785 at 1,400 min
-1
13
13–15
300
SPEC. SHEET NO. GR-1000E-4-00101/EX-01
-3 -
Содержание GR-1000EX-4
Страница 18: ...MEMO...
Страница 19: ...MEMO...
