TACKLIFE PTR01A Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 28

TACKLIFE PTR01A Скачать руководство пользователя страница 9

!

!

INSTALLING THE FREEHAND

CUTTING GUIDE

The freehand cutting guide is designed for

basic freehand cutting with the cutting bit. It

is ideally suited for cutting electrical outlet

holes in drywall.

1.

2.

NOTES:

a)

b)

3.

INSTALLING CUTTING BITS

To loosen and tighten the collet use the collet

wrench supplied with the tool.

Open the freehand cutting guide mounting

collar (1) by pulling the quick release lever

(2) outward (Fig. 2).

Slide the mounting collar onto the bottom

of the motor housing (3).

The mounting collar must be pushed onto

the motor housing as far as it will go.

Rotate the mounting collar to position it to

provide the best visibility to the bit.

Lock the freehand cutting guide onto the

motor housing by pushing the quick release

lever inward toward the mounting collar until

it snaps into the locked position.

WARNING: Do NOT use the

freehand cutting guide with router

bits. The amount of control this

accessory provides is insufficient

and could cause you to lose

control and cause serious injury.

WARNING: Cutting bit and router

bit cutting surfaces are extremely

sharp. Handle with caution.

Fig. 2

- 08 -

«
...
7
8
9
10
11
...
»

Содержание PTR01A





























Отзывы:

Нет отзывов