manualshive.com logo in svg

TACKLIFE PTR01A, Руководство пользователя, Страница: 12 / 28

Поделиться
Скачать
TACKLIFE PTR01A Скачать руководство пользователя страница 12

SPEED CONTROL SWITCH

The spin saw is equipped with a variable speed control located below the ON/OFF switch. To 

run the tool at the slowest speed, rotate the speed control wheel (2) to number “1” (Fig. 6). To 

increase the tool speed, rotate the speed control wheel in the opposite direction. Maximum 

speed will be achieved at “6”.

ADJUSTING THE FREEHAND CUTTING GUIDE

1.

NOTE: 

Set the foot so the cutting bit protrudes beyond the bottom of the cutting guide 1/8" more 

than the thickness of the material being cut. For example, if you are cutting 5/8" drywall, the bit 

should protrude 3/4" beyond the bottom of the cutting guide.

2.

NOTE: 

Hand tightening is normally adequate. If you use a screwdriver (3), do not over tighten 

the locking screw.

Adjust the freehand cutting guide depth by loosening the depth gauge locking screw (1) and 

moving the cutting guide foot  (2) up or down as required (Fig. 7).

Securely tighten depth gauge locking screw.

 

Fig. 6 

Fig. 7 

 

- 11 -

Содержание PTR01A





























Отзывы:

Нет отзывов