TACKLIFE PTR01A Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 28

TACKLIFE PTR01A Скачать руководство пользователя страница 8

!

WARNING: Some of the following symbols may appear on this tool. Study these

symbols and learn their meanings. Proper interpretation of these symbols will

allow for more efficient and safer operation of this tool.

ASSEMBLY AND OPERATING

INSTALLING THE ASSIST HANDLE

The removable assist handle is designed for use when precision control over the tool movement

is desired. Use the assist handle when operating the tool with either the freehand cutting guide

or the circle cutting guide.

1.

2.

3.

NOTE:

The mounting bracket must be pushed onto the motor housing as far as it will go.

4.

Open the mounting collar (1) by pulling the quick release lever (2) outward (Fig. 1).

Slide the mounting collar onto the bottom of motor housing (2). Make sure the key (3) on the

motor housing is aligned with the matching keyway in the mounting collar.

When the key and keyway are aligned, slide the mounting collar fully onto the motor housing

and then rotate the collar clockwise approximately 10° to lock the key and keyway.

Press the quick release lever inward toward the mounting collar to finish locking the mount-

ing collar onto the motor housing.

Fig. 1

- 07 -

«
...
6
7
8
9
10
...
»

Содержание PTR01A





























Отзывы:

Нет отзывов