background image

charging and built-in charging, fast charging current up to 1a, with other 
different specifications of charging head and line, may cause damage to 
the equipment.

10. anti tamper alarm

10.1 Terminal adsorption on a piece of iron (tamper cannot switch is in a 
self-locking  state),  when  a  terminal  is  picked  up,  the  tamper  switch 
bounce, to the platform reporting alarm information.
10.2 At the same time will send a message to the center number or call 
(the premise is to open a text message or telephone alarm function).

11.GPS sleep and wake up

When the terminal is in the intelligent sleep mode, still 3 minutes will enter 
the sleep,  by the sensor  control, if the sensor is detected in the motion 
state, it will automatically wake up GPS.
When the terminal is in a deep sleep state, GPS has been in a state of 
sleep, not affected by the sensor, only the center number dialed terminal 
number or send text messages instructions, will wake up 3 minutes.
When the monitor function is turned on, the central number of the call will 
not  wake  up  the  device,  but  directly  into  the  listening  state,  then  if  you 
need to wake up the device, can only send text messages WAKE#

12. Trouble shooting

12.1

The device is not online or offline on the web platform

12.1.1

First  observe  whether  the  terminal  indicator  is  normal.  If  you 

cannot observe it, please dial the SIM card number of the terminal with 
your mobile phone and determine the status of the terminal according to 
the prompt tone.
● If not connected, indicating that the terminal temporarily cannot connect 
or the GSM signals cannot reach your location

The area where the terminal is located may not cover the GSM signal 

or it may be in a weak signal place such as a basement. Please drive to a 
place with good signal.
● If  it  is  not  connected,  the  reminder  is  that  the  SIM  card  balance  is 
insufficient or it has been shut down.

The terminal SIM card is in arrears, please recharge this SIM card.

● If it is connected and you hear "beep...beep...beep...".

Please  consult  the  operator  of  this  card  whether  the  GPRS  function 

has  been  activated;  you  can  also  use  your  mobile  phone  to  install  this 
SIM card and enter your frequently used web address in the browser to 
check  whether  the  webpage  can  be  opened; If  you  cannot  open  the 
website,  the  SIM  card  has  not  activated  the  GPRS  service,  please 
contact the operator to activate it for you.
● If the terminal is not connected and reminding shutdown
      At this time, the working status of the terminal must be checked. The 

Содержание T2-1














Отзывы: