SYSTEMS Poweramp EH Series Скачать руководство пользователя страница 45

Страница: 45 / 62

4111-0004 — Apr. 2021

Symptom

Possible Cause

Solution

Three-phase units only:

Platform does not rise.

Motor hums, but does

not run.

No voltage is present on

one line.

NOTE: A motor that is

missing voltage on one line

is said to be single-phased.

Check for blown fuses at branch circuit disconnect.

Replace fuse. Determine cause of blown fuse.

Check motor starter as follows:

1. Disconnect wires at load side of starter.

2. Energize the starter.

3. Measure line-to-line voltage at line side of starter.

4. Measure line-to-line voltage at load side of

starter.

5. Line-side and load-side voltages should be

approximately the same. Replace starter if

voltage values are considerably different from

one another.

Check all wiring to motor for high resistance or no

connection.

Three-phase units only:

Platform does not rise.

Motor runs in reverse

Phase reversed.

Reverse any two legs at the branch circuit

disconnect.

Single-phase units only:

Platform does not rise.

Motor energizes, but

does not run.

Line voltage too low.

Check wiring to motor for high resistance. Check for

loose or corroded connections. Check if gauge of

wires to motor are of correct size and specification

for load requirement. Replace if necessary.

Faulty motor centrifugal

switch.

Replace motor.

Faulty motor capacitor.

Replace motor.

Units equipped with

ARTD only:

Platform does not

automatically return to

the cross-traffic position

or operates abnormally.

Auto return proximity switch

not sensing target correctly.

Adjust proximity switch and target as necessary.

See Adjust Auto Return To Dock (ARTD) on pages

36-38.

Faulty proximity switch.

Replace switch.

Loose/corroded wire

connections or broken wire.

Repair or replace wires and connections as

necessary.

TROUBLESHOOTING

Содержание Poweramp EH Series































































Результаты поиска

Содержание Poweramp EH Series

Отзывы:

Похожие инструкции для Poweramp EH Series

Бренды по названию

Популярные бренды

SYSTEMS Poweramp EH Series, Руководство пользователя

Результаты поиска

Содержание Poweramp EH Series

Отзывы:

Похожие инструкции для Poweramp EH Series

Бренды по названию

Популярные бренды