System Sensor Innovair DH100ACDCLPX, Инструкция по установке и обслуживанию

Страница: 5 / 12

��
��
��
�
��
�
�
�
������������
������������
����������
��������
������������
������ ����������������������������������������������������
�
�������������������������������������������������������
�����
���������
�����
�����������
������
������ ������������
D200-33-00 5 I56-1944-07
Figure 8. Wiring diagram for DH100ACDCLPX
to APA451:
H0172-00
A78-2741-00
A78-2740-00
H0155-01
Figure 7. System wiring diagram for 4-wire duct smoke detectors:
Figure 9. Wiring diagram for DH100ACDCLPX to
RTS451/RTS451KEY:
Important Interconnect Notes
• When using the interconnect feature, all
interconnected units must be powered with
the same, independent supply.
• Polarity must be maintained throughout
the interconnect wiring. Connect terminal
12 on unit 1 to terminal 12 on unit 2 and so
on. Similarly, connect terminal 1 on unit 1
to terminal 1 on unit 2 and so on.
• Up to 10 units may be interconnected.
Figure 10. Multiple fan shutdown (interconnect):
1 6
12 16
A B C
FAN
CONTROL
SYSTEM
CONTROL
POWER OR
THERMOSTAT
1 6
12 16
A B
FAN
CONTROL
SYSTEM
CONTROL
POWER OR
THERMOSTAT
DETECTOR 1
C
DETECTOR 2
1 6
12 16
A B
FAN
CONTROL
SYSTEM
CONTROL
POWER OR
THERMOSTAT
C
DETECTOR 10
OUT TO
10 DETECTORS
MAXIMUM
24V
9 10
AVAILABLE POWER INPUTS
ALARM AUXILIARY CONTACTS
FOR FAN SHUTDOWN, ETC.
16 6 17 7 18 8
N.C. C. N.O. N.O. C. N.C.
ALARM AUXILIARY CONTACTS SHOWN IN
STANDBY. CONTACTS TRANSFER DURING
ALARM AS INDICATED BY THE ARROWS.
SUPERVISORY TROUBLE CONTACTS
TROUBLE CONTACTS CLOSED IN ALARM AND STANDBY.
CONTACTS OPEN WHILE DETECTOR PCB OR POWER IS
REMOVED OR WHEN TAMPER FEATURE TIMES OUT. OPEN
CONTACTS SIGNAL TROUBLE CONDITION TO PANEL.
24V
9 10
AVAILABLE POWER INPUTS
ALARM AUXILIARY CONTACTS
FOR FAN SHUTDOWN, ETC.
16 6 17 7 18 8
N.C. C. N.O. N.O. C. N.C.
ALARM AUXILIARY CONTACTS SHOWN IN
STANDBY. CONTACTS TRANSFER DURING
ALARM AS INDICATED BY THE ARROWS.
SUPERVISORY TROUBLE CONTACTS
TROUBLE CONTACTS CLOSED IN ALARM AND STANDBY.
CONTACTS OPEN WHILE DETECTOR PCB OR POWER IS
REMOVED OR WHEN TAMPER FEATURE TIMES OUT. OPEN
CONTACTS SIGNAL TROUBLE CONDITION TO PANEL.
14 3 3 14
4
5
ALARM
INITIATION
CONTACTS
CONTACTS SHOWN
OPEN IN STANDBY.
CONTACTS CLOSE
IN ALARM.
4
5
ALARM
INITIATION
CONTACTS
CONTACTS SHOWN
OPEN IN STANDBY.
CONTACTS CLOSE
IN ALARM.
ALARM
INITIATION
LOOP
UL LISTED 4-WIRE
CONTROL PANEL
FIRST DETECTOR IN THE LOOP
DH100ACDCLPX
LAST DETECTOR IN THE LOOP
DH100ACDCLPX
EOL RESISTOR
SPECIFIED BY
PANEL MANUFACTURER
CONNECT POWER SOURCE
TO APPROPRIATE TERMINALS
OF EACH DETECTOR. SEE
SPECIFICATIONS FOR
ADDITIONAL POWER SUPPLY
INFORMATION.
FOR WIRING OF AUXILIARY
DEVICES, REFER TO
MANUFACTURER'S
INSTALLATION INSTRUCTIONS
OR CONTACT MANUFACTURER.
NOTE: THE SUPERVISORY RELAY NOW
PROVIDES A "FORM C" CONTACT FOR
CUSTOMIZED APPLICATIONS.
FOR STANDARD APPLICATIONS, ONLY
THE "NO" CONTACT IS USED
POWER INPUTS ACCEPT
24 VDC, 24 VAC 50-60 HZ,
CONNECT POWER SOURCE
TO APPROPRIATE TERMINALS
OF EACH DETECTOR.
AUX. CONTACT RATINGS
10A @ 30 VDC RESISTIVE
100mA MINIMUM @ 5 VDC
1/4 HP @ 240 VAC
1/8 HP @ 120 VAC
NOT INTENDED FOR
CONNECTION TO CONTROL
PANELS.
TROUBLE CONTACT RATING
2.0 A @ 30 VDC resistive
2.0 A @ 125 VAC resistive
+
��
��
��
�
��
�
��
�
�
� ������������
������������
����������
��������
������������
�����
����
���������������
�����������
�����
������������ ����������������
�
�
�
�
�������������
��������������
��������������
�
CAUTION
Do not loop wire under terminals when wiring detectors. Break wire runs to provide system supervision of connections.