manualshive.com logo in svg

Symmetricom 9611B, Руководство пользователя

Поделиться
Скачать
Symmetricom 9611B Скачать руководство пользователя страница 16

Installation

Connect a RS232 serial command line interface cable from the 9611B to the PC serial port, (this is a
straight cable, not a null modem cable).

TurningSystemOn

The 9611B can be operated directly with the default settings that it comes with from the factory. The
factory default values have been set to distribute the most common suite of signals. A list of the fac-
tory default values follows this section. When using the 9611B in this mode, simply connect AC power
after making the connections listed in the previous section. After the 9611B is powered up, press the
ALARM button to clear any alarms.

To change the factory default values, and to take full advantage of the flexibility of the 9611B, a com-
munications program such as Hyperterm is needed to communicate to the 9611B, via the RS232
serial port. The following procedure assumes the desire to run the 9611B with the provision to change
the factory default values.

Note: When using XMODEM in Hyperterm, for best results, use the version of XMODEM that uses
128 byte blocks.

1. On the PC, run the serial port communication program (see the Command Line Interface section
that follows).

2. Apply AC power (-01 option).

3. On the 9611B front panel, press the ALARM button to clear any alarms.

4. Follow the "How to Set Up the 9611B for Operation" instructions.

Default Values

Impedance = 50 ohms
Frequency = 1, 1 Hz to <10 Hz
Fault A: input = enabled, level low
Fault B: input = enabled, level low
voltage: 0.25 Volts is set
switch: Input A is selected
Gain setting jumper = position B for high gain

Installation Warnings

Please review the following warnings before proceeding with the installation of the 9611B.

ChassisGroundingScrew

The chassis grounding screw provides a secure contact for grounding the unit to a reliable earth
ground.

Page 4

..........................................................................

9611B_UserGuide_RevA.pdf

Содержание 9611B



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды