manualshive.com logo in svg

Sym Quad Raider 600, Руководство по обслуживанию

Поделиться
Скачать
Sym Quad Raider 600 Скачать руководство пользователя страница 228

18. ELECTRICAL SYSTEM 

 

18-4 

 

Battery 

Removal 

Remove the seat, and then you can see the 

battery. 
Disconnect the negative cable terminal first, then 
the positive cable terminal. 
Remove the battery clamp, and then remove the 
battery. 
 
 
 
 
 
 

Voltage Check 

Use the digital voltmeter to check the voltage of 
the battery. 

Voltage: 
Fully charged:  13.0~13.2 V at 20

℃

 

Undercharged:  Below 12.3 V at 20

℃

 

 
Charging 

Connect the positive terminal (+) of the charger to 
the battery positive terminal (+). 
Connect the negative terminal (-) of the charger to 
the battery negative terminal (-). 

 Standard 

Maximum 

Charging current 

1A 

4.0A 

Charging time 

5H 

1H 

 

 Warning 

 

Keep flames away while recharging. 

 

Charging is completely controlled by the 
ON/OFF switch on the charger, not by 
battery cables. 

 

 Caution 

 

Never rapid charge the battery unless in 
emergency. 

 

Verify the battery is recharged with correct 
current and duration prescribed above. 

 

Large current and fast time to charge will 
render damage to the battery. 

 
When installing the battery, coat the cable terminal 
with grease.

 

 

 

 

 

 

 

 

To this chapter contents 

Clamp 

Содержание Quad Raider 600
























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды