manualshive.com logo in svg

Sym Quad Raider 600, Руководство по обслуживанию

Поделиться
Скачать
Sym Quad Raider 600 Скачать руководство пользователя страница 142

To this chapter contents 

 

11. A.C. GENERATOR/STARTING CLUTCH 

 

Right Crankcase Cover Removal 

Remove the left 

footrest.

 

Drain the engine oil and coolant, and then remove 
coolant hoses. 
Remove 5 bolts from the recoil starter cover. 
Remove the recoil starter cover and gasket. 
Remove the water pump cover (5 bolts) 
 
 
 
 
 
 

A.C. Generator Removal 

Remove the connector bolt and starter pulley. 
Remove 12 mounted screws from the right 
crankcase cover and then remove it. 
 
 
 
 
 
 
 
 
 
 
Remove 5 screws from right crankcase cover. 
 

 

 
 
 
 
 
 
 
 
 
 
 
Remove the stator.

 

 

 

Water pump cover 5 bolts 

5 bolts

 

 

 

 

 

 

 

12 screws

Coolant hoses.

Connector bolt and starter pulley 

5 screws

11-3 

Содержание Quad Raider 600
























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды