manualshive.com logo in svg

Sym Quad Raider 600, Руководство по обслуживанию

Поделиться
Скачать
Sym Quad Raider 600 Скачать руководство пользователя страница 189

 

15. FRONT BRAKE & FRONT WHEEL 

15-9 

To this chapter contents 

 

Brake Disk   

Inspection 

Visually check the brake disk for wear or spoilage. 
Measure the thickness of the disk at several 
places. Replace the disk if it has exceeded the 
service limit. 

Allowable limit: 2.5 mm 

 
 
 
 
 
 
Remove the brake disk from wheel hub. 
Check the disk for deformation and bend.   

Allowable limit: 0.30 mm 

 Caution 

 

The dirty brake lining or disk will reduce the 
braking performance. 

 

Brake lining includes the asbestos ingredient; 
do not use the air-gun clean the caliper, the 
operator should dress the mouthpiece and 
the glove, use vacuum cleaner to clean it.

 

 

Front Brake Master Cylinder 

Master Cylinder Removal

 

 Caution 

Do not let foreign materials enter the cylinder.

 

 Caution 

The whole set of master cylinder, piston, spring, 
diaphragm and circlip should be replaced as a 
set.

 

 
 
 
 
 
Push the lead of brake light switch, and then 
remove brake light switch. 
Drain out the brake fluid. 
Remove the brake lever from the brake master 
cylinder. 
Remove the brake hose. 
Remove the master cylinder socket bolts and the 
master cylinder. 

 

 

 

 

 

 

2 socket bolts

 

Micrometer

Brake disk

Brake light switch

Содержание Quad Raider 600
























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды