background image

2. Maintenance Information 

2-5

 

Air Cleaner 

Air element 

Remove the air cleaner cover (6 screws).   
Remove the lock plate from the element of air 
cleaner. 
Check the element if dirt or damaged. 
If it dirt, clean it with solvent and then soap it into 
cleaning engine oil after cleaned.    Finally, 
squeeze it.   
Replace it with new one if dirt or damaged. 
 

 

Caution

 

 
 
 
 

 

 

 
 

 

 

Throttle Valve Operation 

Have a wide open of throttle valve as handle bar 
in any position and release it to let back original 
(full closed) position. 
Check handle bar if its operation is smooth. 
Check throttle valve cable and replace it if 
deteriorated, twisted or damaged. 
Lubricate the cable if operation is not smooth. 
Measure handle bar free play in its flange part. 

Free play

2~6 mm 

 

Adjustment can be done in either ends. 
Secondary adjustment is conducted from top 
side. 
Remove rubber boot, loosen fixing nut, and then 
adjust it by turning the adjustment nut. 
 
 
 

2~6 mm 

Fixing nut 

Adjustment nut 

Rubber boot

6 screws

 

Make sure that the air cleaner cover had 
been installed properly after installation 
because improperly installation will cause 
foreign sucking into cylinder. 

 

Do not wet the air cleaner as washing the 
motorcycle.    Or it may effect engine 
performance. 

This chapter Contents

Содержание ATTILA RS-21 EFi 150





































































































Отзывы: