Sykes-Pickavant 02695000 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 19

Sykes-Pickavant 02695000 Скачать руководство пользователя страница 18

18

ADDITIONAL INSTRUCTIONS

REPLACING THE LASER VISOR BATTERIES

Unscrew the two screws on the cover of the laser
visor and replace the 3 1.5V size AA batteries making
sure you put them in the right way up; close the visor
again fixing the cover on using the screws provided.

WARNING!

For longer duration we recommend using alkaline
batteries.

REPLACING THE BATTERIES ART. 2400/D

Should the headlight beam tester device battery need
replacing proceed as follows:
with  a  crosshead  screwdriver  unscrew  the  two  self-
tapping  screws  fixing  the  battery  support to the back
cover of the optical box.
Remove  the  support  and  extract  the  battery,  detach
the  connector  and  replace.  Reassemble,  repeating
the  operations  described  for  disassembly  in  the
reverse order.

WARNING!

For longer duration we recommend using alkaline
batteries.

REPLACING THE BATTERIES ART. 2400/I

To  replace  the    12Vcc  2Ah  lead  battery  proceed  as
follows:
open  the  optical  box,  removing  the  cover,  be  careful
not to damage the electrical connections.
The  battery  is  attached  behind  the  test  panel,  to
remove  it  unscrew  the  nut with a socket wrench and
unhook  the  attachment  bracket.  Remove  the  battery
and replace with a new one making sure you put it in
the right way up.
Reassemble  and  check  the  movement  of  the  test
panel before putting the cover back on.

«
...
16
17
18
19
»

Содержание 02695000




















Отзывы:

Нет отзывов