Sykes-Pickavant 02695000 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 19

Sykes-Pickavant 02695000 Скачать руководство пользователя страница 11

11

ALIGNMENT OF THE VEHICLE

POSITIONING

Place the headlight beam tester in front of the right
headlight of the car at a distance of approx. 20cm,
measure the height from the ground to the centre of the
headlight and adjust the optical box to the corresponding
height using the graduated scale on the column. Use the
top of the sliding block as an index on the scale.

POSITIONING WITH THE HELP OF THE LASER
POINTER

By turning the wheel on the back of the optical box to the
“0”,  position,  corresponding  to  the  centre  of  the  lens,  a
laser  ray  will  be  emitted  which  will  help  you  to  align  the
centre of the headlight.
When  you  set  the  inclination  of  the  headlight  using  the
wheel the laser will switch off automatically.

At  the  end  of  every  test,    to  prevent  the  batteries  from
going flat, turn the inclination wheel situated at the back of
the optical box to a percentage other than 0% ( e.g. 1%)

WARNING!

Do not look at the laser beam directly during this
operation and make sure that it is not pointing at people
near the workstation.

«
...
9
10
11
12
13
...
»

Содержание 02695000




















Отзывы:

Нет отзывов