SWS Power Tools 66630 Скачать руководство пользователя страница 13

Страница: 13 / 22

SKU 66630

For technical questions, please call 1-800-444-3353.

Page 13

Aligning and Adjusting the Rip Fence (146)

warning!

A misaligned Fence can

cause kickbacks and jams. To reduce

risk of injury, always maintain proper

Fence alignment. The Rip Fence

must be parallel with the Blade and

Table grooves.

2. Lift up the Fence Handle (26) and

move the Fence along the gauge slot

until sliding it to the desired location.

3. Verify that Fence is parallel, then

push down on the Handle to lock the

Fence in place.

4. A Draw Pole (132) locks the Fence

in place. To adjust the Draw Pole,

loosen the Bolt (20) that connects the

Draw Pole to the Fence.

warning!

The Fence must be

properly aligned to the gauge slot to

prevent kickback during ripping.

6. To check for proper alignment, po-

sition the Fence next to the gauge

slot and clamp Fence to the Table

by pushing down on Fence Handle.

Once locked, the edge of the Fence

should be parallel to the gauge slot.

Adjusting Table Insert (112)

Lower the Blade by turning the Hand-

wheel clockwise.
Loosen the two Table Insert Bolts

(12).
Adjust the Table Insert and retighten,

making sure to not overtighten. Do-

ing so can cause the Table Insert to

bow or bend.
If the Table Insert is slightly above

the Table, tighten the two Table Insert

Bolts until the Table Insert is flush

with or slightly below the Table sur-

face.

Miter Gauge (100) Operation and

Adjustment

When straight cross-cutting (the

Blade is set at 90° to the Table) the

Miter Gauge can be used in either

table slot.
When bevel cross-cutting (the Blade

is tilted away) only use the Miter

Gauge in the right table slot where

the Blade is titled away from the Miter

Gauge and your hands.
To operate the Miter Gauge, loosen

the Gauge’s Lock Knob (101) and

move the Gauge to the desired angle,

then tighten Knob.

Adjusting Blade Parallel To Miter Gauge

Slots

warning!

Make sure to unplug

Table Saw before making any adjust-

ments to Blade.
To prevent kickback and ensure ac-

curate cuts when cutting, the Blade’s

angle in relation to the Miter Gauge

should be regularly checked. If any

adjustments are needed:
Remove the Blade Guard (113).

Raise the Blade to its highest position

and adjust to Blade so that it is 90° to

the Table.
Mark a Blade tooth at the front of the

Table Saw with a marker.
Using a square or ruler (not includ-

ed), place the square against the

Miter Gauge slot and adjust the flat

Содержание 66630























Результаты поиска

Содержание 66630

Отзывы:

Похожие инструкции для 66630

Бренды по названию

Популярные бренды

SWS Power Tools 66630, Руководство по установке и эксплуатации

Результаты поиска

Содержание 66630

Отзывы:

Похожие инструкции для 66630

Бренды по названию

Популярные бренды