background image

1080i(60/59.94/50/30/29.97/25/24/23.98)
720p(60/59.94)
1080psf(30/29.97/25/24/23.98)

Trouble-shooting

No display

Image or color 

abnormal

No audio 

output

The power is not turned on

Unstable power voltage

BNC or HDMI cable loose

contact or not correctly 

connected
The attached battery is 

no power

Using DIY power supply but 

the polarity is reversed

Bad contact of BNC or 
HDMI cable

Video signal has Interference

Improper adjustment of the

color parameters

Distortion of the image

Set to Blue only or Mono

Turn on the “Focus Assist” 

function
Turn on the “False Color” 
function

Bad contact of signal cable

Wrong connection or bad 
contact of Audio cable

Please check if the power is connected, and then 
press ”POWER” button to turn on the monitor

Reconnect to power supply

Check and correctly connect the BNC or HDMI cable

Change battery

Refer to the provided power supply, reconnect the 
power.

Change cable

Remove the interference source(s)

Adjust the “Recall profile” to “Factory” under 

“System” submenu

Reset the Aspect ratio

Turn the Blue only /Mono off 

Turn off the “Focus Assist” function

Turn off the “False Color” function

Change signal cable

Connect to the correct input socket.

Symptom                  Possible Causes                    Solution

21

Содержание FM-16B























Отзывы: