background image

GB.SILVERF120.181005

We reserve the right to alter specifications.

www.swegon.com     3

3440

1070

1070

1868

1170

2350

1861

2930

1.1 General

All staff concerned must acquaint themselves with these 
instructions before beginning any work on the unit. Any 
damages to the unit or parts of it due to improper han-
dling or misuse by the purchaser or the fitter cannot be 
considered subject to guarantee if these instructions have 
not been followed correctly. 
The product identification label is affixed on the inspection 
side of the air handling unit. Refer to the particulars on the 
product identification plate when you contact Swegon. 
The air handling unit is supplied in packaged condition. 
Possible ordered accessories are supplied in separate pack-
aging with the unit.

1.2 Transport within the site

Before removing the transport pallet/transport cradle, if 
used, determine whether a forklift truck or a pallet trans-
porter will be used for further transporting the unit within 
the site to the spot where it will be installed.

1.3 Parts packed together with the unit

Components such as the commissioning plates, bolts and 
document pocket are supplied in separate packaging and 
delivered together with the air handling unit.

1.3.1 Document pocket

Secure the document pocket to the exterior of the air 
handling unit or another appropriate place. 

1.4 Arrangement

The air handling unit must be mounted horizontally on a 
flat and firm supporting surface and this surface must be 
constructed in a way enabling it to support the weight of 
the unit.
When installing the air handling unit and connecting pipe-
work and electric cables, make sure that adequate free 
space is provided for opening the inspection doors and 
covers and withdrawing functional sections, such as filter 
cassettes and fan assemblies, clear of the unit casing. 

Inspection space required

A clear space of 1,000 mm should be provided in front of 
the unit for opening the inspection doors.

1. Installation

1.5 Method of delivery

1.5.1 SILVER C RX

The SILVER C RX 120 is normally supplied in five separate 
sections: Two fan sections, two filter sections and one 
heat exchanger section. 
The heat exchanger section can also be supplied split into 
two casing sections and rotor, in which case the rotor is 
supplied tilted in a transport cradle (transport height = 
2,930 mm, minimum transport width = 2,350 mm). See 
Section 1.7 for installation particulars.
For other dimensions and weights, see Section 2.1.

Heat exchanger section supplied as a separate unit

Heat exchanger section, sup-
plied split into two casing sec-
tions and rotor

Rotor, Ø 3150

Transport cradle

3440

1070

1070

1868

1170

2350

1861

2930

1.5.2 SILVER C CX

The SILVER C CX 120 is supplied in six separate sections: 
Two fan sections, two filter sections and two coil heat 
exchanger sections.
For dimensions and weights, see Section 2.2.

Содержание SILVER C CX 100

























Отзывы: