manualshive.com logo in svg

swaploader SL-240, Руководство по эксплуатации и частям


Поделиться
Скачать
background image

28JUL09 

[Hoist Models: SL-220, SL-222 & SL-240] 

 

INSTALLATION INSTRUCTIONS 

 
1. 

Review all directions and diagrams provided before starting the C.V.S. installation. 

 
2. 

Attach the base plate bracket [Part No. 23H76] to the C.V.S. sub-assembly [Part No. 

12H01] with fasteners provided (See drawing 52H21 

Section View A-A

). 

 
3. 

Position the C.V.S. sub-assembly with attached base plate bracket on side of the 

mainframe z-channel (See drawing 52H21).  Drill the necessary 13/32 Dia. holes into 
the z-channel using the C.V.S. sub-assembly with attached base plate bracket as the 
pattern to aid in locating hole placement.  To allow for C.V.S. sub-assembly [Part No. 
12H01] fastener clearance some notching of the z-channel lip may be necessary. 

 
4. 

Attach the C.V.S. sub-assembly and base plate bracket to the mainframe z-channel with 

fasteners provided (See drawing 52H21). 

 
5. 

Drain hydraulic oil level in the tank to just below the 1 1/4” NPT Port. 

 
6. 

Remove the 90 degree hydraulic fitting [Part No. 11P07] that connects the upper 

hydraulic steel tubing to the top bulkhead fitting (See drawing 90H97).  Replace with 
a swivel tee hydraulic fitting [Part No. 12P44] and retighten the hydraulic fittings (See 
drawing 90H85). 

 
7. 

Remove the 1 1/4" NPT plug from the hydraulic tank.  Install hydraulic fittings 12P20 & 

12P92 as shown and tighten (See drawing 90H85). 

 
8. 

Install the two 90 degree hydraulic fitting [Part No. 12P69] into the hydraulic valve on the 

12H01 C.V.S. sub-assembly and tighten (See drawing 90H85). 

 
9. 

Attach the hydraulic hose [Part No. 13P02] between the C.V.S. hydraulic valve and 

swivel tee hydraulic fitting [Part No. 12P44], and tighten (See drawing 90H85). 

 
10. 

Determine the length of hose required to route the C.V.S. hydraulic valve to the hydraulic 

tank; the hydraulic hose [Part No. 12P93] may need shortened 
prior to final installation (See drawing 90H85) especially if 
excess length exists.  The hydraulic hose [Part No. 12P93] 
comes with a reusable fitting that can be removed for purposes 
of shortening the hose.  Remove the reusable fitting and 
shorten hose assembly as required.  After hose has been 
shortened, lubricate the insert threads of the fitting and the I.D. 
of the hose (See Fig. 1).  Measure 1 3/16 inches from the end 
of the hose and mark the hose for the socket depth.  Screw the 
hose into the socket (left-hand thread) to the depth marked on 
the hose.  Screw the insert into the socket until the insert 
touches the socket.  Clean the inside of the hose assembly by 
either clean compressed air through it or by flushing it. 

CONTAINER VARIABILITY SYSTEM ASSEMBLY 

(52H21) 

Figure 1 

Содержание SL-240













































































































































Отзывы:

Нет отзывов

Похожие инструкции для SL-240

Mercedes-Benz Actros Operating Instructions Manual preview
Actros
Бренд: Mercedes-Benz Страницы: 418
Kenworth T440 2010 Manual preview
T440 2010
Бренд: Kenworth Страницы: 120
Fisher-Price RC Truck 72824 Instructions preview
RC Truck 72824
Бренд: Fisher-Price Страницы: 4
Pierce Pumper Operation & Maintenance Manual preview
Pumper
Бренд: Pierce Страницы: 66

Бренды по названию

Популярные бренды

Загрузить еще бренды