swaploader SL-240 Скачать руководство пользователя | Manualshive

Страница: 35 / 140

background image

SL-240.INS

2-17

05/2020

PUMP INSTALLATION

1.

Install the hydraulic pump to the P.T.O. (Bolts are not provided).

2.

Install the hydraulic fittings into ports on the hydraulic pump as shown on Drawing No.
90H98.

3.

Connect the suction hose assembly to the hydraulic tank (1 1/4" I.D. hose) and route to
the hydraulic pump in as short and straight line as possible.  Be sure to route the hose
clear of exhaust components and of the drive shaft.  Extra hose is provided so the hose
can be shortened to an appropriate length.  Install the hose on the hose barb fittings at the
tank and at the pump and secure with the hose clamps provided.

NOTE: Prior to startup, this hose must be filled with oil.

4.

Connect pressure hose assembly (3/4 inch I.D. hose) to control
valve inlet and route to the pump the same as the suction line.
This hose is provided with only one fitting, so the hose can be
shortened to appropriate length.  Remove the hose and shorten as
required.  After the hose has been shortened, lubricate the insert
threads of the fitting and the I.D. of the hose.  Measure 1 3/16
inches from the end of the hose and mark the hose for the socket
depth.  Screw hose into the socket (left-hand thread) to the depth
marked on the hose.  Screw insert in socket until insert touches
the socket.  Clean the inside of the hose assembly by either
blowing clean compressed air through it or by flushing it.  Install
the completed hose assembly to the inlet port of the control
valve assembly and the outlet port of the hydraulic pump.

5.

Tie up the pressure and suction hoses as necessary. Again, be
sure the hoses are routed to avoid exhaust components and to
stay clear of the drive shaft.

«
...
33
34
35
36
37
...
»

Содержание SL-240













































































































































Отзывы:

Нет отзывов

Похожие инструкции для SL-240

Бренд: EP Equipment Страницы: 46

Бренд: Wesco Страницы: 11

Бренд: HELI Страницы: 82

Бренд: HELI Страницы: 90

Бренд: Scheppach Страницы: 112

Бренд: Jacobsen Страницы: 23

Бренд: Total Source Страницы: 11

Бренд: MARCOLIN Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды