swaploader SL-160 Скачать руководство пользователя | Manualshive

Страница: 16 / 94

background image

Section II: Installation

2.0.INS.SL-160

CONTROLS INSTALLATION – MANUAL

1. Attach the valve mount bracket (

Pt.

No. 10H51

) to the main frame as

indicated on

Pg. 5-11

with the

fasteners provided (see

Pg. 5-7

).

2. Mount the hydraulic control valve

assembly (

Pt. No. 21P32

) to the valve

mount bracket as shown on

Pg. 5-11

with the fasteners provided.

3. Install the hydraulic adapters, connect

the hydraulic tubing & hoses (

Pt. Nos.

12P53, 12P59, & 13P12

) to the

control valve assembly as indicated
on

Pg. 5-9.

The tubing should be

supported by the clamp assemblies
that are provided in the Loose Parts
Box (see

Pg. 5-7

).

4. Determine the best location in the cab

for the control levers (

Pt. No. 20P08

).

The location should be such that the
controls can be easily reached while
operating the truck. A control lever
console (

Pt. No. 20P09

) is provided to

facilitate the mounting of the control
levers

(see Pg. 5-11)

.

5. Assemble and install the control lever

console (see

Fig. F

). Typically, the

console is fastened to the floor of the
cab and the control cables are routed
through additional holes drilled in the
floor. Your installation may require
that additional brackets be fabricated,
or other modifications made.

6. Attach the control cables to the

control levers and route the cable
through the holes in the cab.  Install
the control levers in the console.  Levers should be installed such that when the levers are
pushed forward the control cable is extended.  See

Pg. 5-11

(Manual Control Assembly) for

control lever orientation.

7. Route the cables to the control valve location and attach them to the control valve with the

bonnet connection kits provided (

Pt. No. 20P10

). See the following instruction sheet for

installation procedures.  The control cables supplied are 84 inches long.  Your mounting
may require different length control cables, which can be purchased locally or through
SwapLoader.  Take proper care when routing the control cables, as a good cable path is
essential for a proper operating system.  Keep bends in the cable path to a minimum and be
as generous as possible.  Under no circumstances should any bend be tighter than an 8"

Figure F

2-4

«
...
14
15
16
17
18
...
»

Содержание SL-160































































































Отзывы:

Нет отзывов

Похожие инструкции для SL-160

Бренд: J&M Страницы: 25

LYNX RADIEN UTILITY ACE 2022 Series

Бренд: BRP Страницы: 252

Бренд: Joyner Страницы: 40

Бренд: Club Car Страницы: 60

Бренд: Craftsman Страницы: 80

Бренд: X-TREME Страницы: 26

Sportsman 850 Touring EPS

Бренд: Polaris Страницы: 167

Бренд: Daimler Страницы: 90

Бренд: Yamaha Страницы: 166

GROUND FORCE GO KART V.1+

Бренд: Razor Страницы: 2

Бренд: Baja motorsports Страницы: 6

Бренд: Thump Страницы: 78

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 2

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 36

Бренд: Toro Страницы: 40

Бренд: Toro Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды