Swann SwannSecure Скачать руководство пользователя страница 2

2

Important Information

FCC Verification

This equipment has been tested and found to comply with the limits for 

Class B digital device, pursuant to part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and 

can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio 

or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference 

by one or more of the following measures:
•  Reorient or relocate the receiving antenna
•  Increase the separation between the equipment and the receiver
•  Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected

•  Consult the dealer or an experienced radio/TV technician for help
These devices comply with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions: 
•  These devices may not cause harmful interference, and 
•  These devices must accept any interference received, including in-

terference that may cause undesired operation

Important Note: 

All jurisdictions have specific laws and regulations re-

lating to the use of cameras. Before using any camera for any purpose, 

it is the buyer’s responsibility to be aware of all applicable laws and reg-

ulations that prohibit or limit the use of cameras and to comply with the 

applicable laws and regulations.

FCC Regulation (for USA): Prohibition against eavesdropping

Except for the operations of law enforcement officers conducted under 

lawful authority, no person shall use, either directly or indirectly, a de-

vice operated pursuant to the provisions of this Part for the purpose 

of overhearing or recording the private conversations of others unless 

such use is authorized by all of the parties engaging in the conversation.

FCC Warning:

 The transmitter must not be co-located or operated in con-

junction with any other antenna or transmitter.  This equipment complies 

with the FCC RF radiation exposure limits set forth for an uncontrolled envi-

ronment. This equipment should be installed and operated with a minimum-

distance of 20cm between the radiator and any part of your body.

Warning: 

Changes or modifications made to this device not approved 

expressly by the party responsible for compliance could void the user’s 

authority to operate the equipment.

Important Safety Instructions

•  Make sure product is fixed correctly and stable if fastened in place
•  Do not operate if wires and terminals are exposed
•  Do not cover vents on the back of the device and allow adequate 

space for ventilation

Default Password Information

To ensure your privacy, this device supports password protection.
The default, all-access username is 

admin

, the default password is 

12345

.

To ensure your ongoing privacy, we strongly recommend setting a pass-

word as soon as possible. Choose something that you’ll remember, but 

that others would be unlikely to guess.

Содержание SwannSecure


















Отзывы: