Suzuki SMD7 Скачать руководство пользователя страница 23

3.  SETTINGS AND ADJUSTMENTS

38

8. Tap the [

u

] icon at the top-right corner of the menu to close the menu.

3.7.2

How to align the antenna heading

You have mounted the antenna unit facing straight ahead in the direction of the bow. 
Therefore, a small but conspicuous target dead ahead visually should appear on the 
heading line (zero degrees).

In practice, you will probably observe some small bearing error on the display because 
of the difficulty in achieving accurate initial positioning of the antenna unit. The follow-
ing adjustment will compensate for the error.

1. Turn the boat towards a target. The target should be oriented directly forward of 

the bow.

2. Tap the [Home] icon to show the [Home] screen, then tap [Settings] => [Radar] => 

[Initial Setup], to show the radar settings.

3. Scroll to the bottom of the menu, then tap [Antenna Heading Align]. The system 

switches to the Radar page.

The data box at the bottom-right of the radar page shows indications for "Head-
ing". The radar page also show a [Cancel] button and a [Save] button at the top of 
the page.

4. Use the range slider to adjust the heading. Tap the plus/minus, or drag the slider 

until the target selected at step 1 is displayed at the top-center of the screen.
Confirm that the "Heading" indication at the bottom-right of the screen shows the 
correct offset value.

5. Tap [Save] to save the settings and return to the standard radar page.

000

010

020

030

040

050

060

070

080

090

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340

350

a

Target

Correct bearing
(relative to heading)

Antenna mounted error
to port 
(HDG SW advanced)

Picture appears
deviated clockwise.

000

010

020

030

040

050

060

070

080

090

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340

350

b

Target

Apparent position

of target

Correct bearing
(relative to 
heading)

Correct bearing
(relative to 
heading)

Apparent
position of
target

Apparent
position of
target

Antenna mounted error
to starboard 
(HDG SW delayed)

Picture appears
deviated counterclockwise.

Front of antenna

Front of antenna

a

b

39

4.

INPUT/OUTPUT DATA

The SMD7/9 can connect to temperature sensors, speed sensors and other 
NMEA0183 or NMEA2000 compatible sensors. To connect and communicate with 
most sensors, sensor settings in the [Interface] menu must be completed.

4.1

How to access the [Interface] menu

The [Interface] menu contains menus for NMEA0183 and NMEA2000 devices. To ac-
cess the Interface menu, follow the procedure below.

1. Tap the [Home] button at the top-left of the screen to show the [Home] page.
2. Tap [Settings] => [Interface]. The [Interface] menu appears.
For the sake of brevity, above two steps are written as "Open the Interface menu" in 
the following sections.

4.2

How to set up the NMEA0183 port

1. Open the [Interface] menu.
2. Tap [NMEA0183 Setup]. The [NMEA0183 Setup] menu appears.
3. Tap [Baud rate], then select the baud rate for your NMEA0183 sensors.
4. Tap the [<] at the top-left of the [Baudrate] options to go back to the [NMEA0183 

Setup] menu.

5. Tap [Format], then select the NMEA0183 format for your NMEA0183 sensors.
6. Tap the [<] at the top-left of the [Format] options to go back to the [NMEA0183 Set-

up] menu.

7. Tap the [

u

] at the top-right of the screen to close the menu.

4.3

How to select a data source

1. Open the [Interface] menu.
2. Tap [Select Input Device].
3. At the left side of the [Select Input Device] menu, tap the data whose sensor you 

want to set up. The [Input Device] list appears to the right of the screen.

4. Select the input device (data source).

• 

[Internal GPS]

: Uses the internal GPS beacon to calculate/display data.

• 

[Internal FF]

: Uses the internal Fish Finder to calculate/display data.

• 

[NMEA0183]

: Uses the connected NMEA0183 sensor to calculate/display data.

• 

[NMEA2000 Auto]

: Automatically selects a NMEA2000 device (connected to 

the same network) to calculate/display data. If communication with the connect-
ed device is lost or interrupted, the next available NMEA2000 device for that 
data type is selected.

Содержание SMD7












































Отзывы: