Suzuki SMD7 Скачать руководство пользователя страница 10

1.  INSTALLATION

12

19°-22° transom angle (small aluminum and fiberglass boats)

: Position the 

shim with the tapered end up.

3. If the bracket has been temporarily fastened to the transom, remove it. Apply a 

marine sealant to the threads of the three #10 x 1-1/4” self-tapping screws to pre-
vent water seeping into the transom. Screw the bracket to the hull. Do not tighten 
the screws completely at this time.

4. Repeat step 1 to ensure that the angle 

of the sensor is correct.

Note: 

Do not position the sensor farther 

into the water than necessary to avoid 
increasing drag, spray, and water noise 
and reducing boat speed.

5. Using the vertical adjustment space on 

the bracket slots, slide the sensor up or 
down to provide a projection of 3 mm (1/
8”). Tighten the screws.

How to attach the sensor to the bracket

1. If the retaining cover near the top of the 

bracket is closed, open it by depressing 
the latch and rotating the cover down-
ward.

2. Insert the sensor's pivot arms into the slots 

near the top of the bracket.

3. Maintain pressure until the pivot arms click 

into place.

4. Rotate the sensor downward until the bottom 

snaps into the bracket.

5. Close the retaining cover to prevent the 

accidental release of the sensor when your 
boat is underway.

How to route the cable

Route the sensor cable over the transom, through a drain hole, or through a new hole 
drilled in the transom above the waterline.

Never cut the cable or remote the connector; this will void the warranty. Always wear 
safety goggles and a dust mask.

1. If a hole must be drilled, choose a location well above the waterline. Check for 

obstructions such as trim tabs, pumps, or wiring inside the hull. Mark the location 
with a pencil. Drill a hole through the transom using a 19 mm or 3/4” bit (to 
accommodate the connector).

2. Route the cable over or through the transom.

Cable cover

Cable 
clamp

50 mm (2")

Hull projection 3 mm (1/8")

Step 1

Step 2

Step 3

Step 4

Latch

Pivot 
arm

Slot 

Retaining 
cover

1.  INSTALLATION

13

3. On the outside of the hull secure the cable against the transom using the cable 

clamps. Position a cable clamp 50 mm (2") above the bracket and mark the 
mounting hole with a pencil.

4. Position the second cable clamp halfway between the first clamp and the cable 

hole. Mark this mounting hole.

5. If a hole has been drilled in the transom, open the appropriate slot in the transom 

cable cover. Position the cover over the cable where it enters the hull. Mark the 
two mounting holes.

6. At each of the marked locations, use a 3 mm or 1/8” bit to drill a hole 10 mm 

(3/8”) deep. The prevent drilling too deeply, wrap masking tape around the bit 10 
mm (3/8”) from the point.

7. Apply marine sealant to the threads of the #6

u

1/2” self-tapping screw to prevent 

water from seeping into the transom. If you have drilled a hole through the 
transom, apply marine sealant to the space around the cable where it passes 
through the transom.

8. Position the two cable clamps and fasten them in place. If used, push the cable 

cover over the cable and screw it in place.

9. Route the cable to the display unit being careful not to tear the cable jacket when 

passing it though the bulkhead(s) and other parts of the boat. To reduce electrical 
interference, separate the sensor cable from other electrical wiring and "noise" 
sources. Coil any excess cable and secure it in place with zip-ties to prevent 
damage.

1.3.5

Matching box (required for 50/200-1T transducer)

The matching box (Available as an optional extra. Type: MB-1100, Code No.: 000-
041-353) is required to connect the optional 50/200-1T transducer.

*: With 10P connector cable

**: For connecting two transducers

Part

Type

Code no.

Qty

Matching Box*

MB-1100

000-041-353

1

Crimp-on Lug

FV1.25-3 (LF)

000-166-756-10

6

Cord Lock**

NC-1

000-168-230-10

1

Vinyl Sheath

Taping

Shrink Tubing

Shield

Crimp-on Lug
FV1.25-3 (LF)

Shield

TB2

J2

J1

02P6348

TB1

Red

White

Green

Black

Blue
Green

Black

Cover unused 
cable entrance

Cover unused 
cable entrance

Detach the grommet; 
attach the cord lock

Detach the grommet; 
attach the cord lock

Jumper block setting
J2: No output reduction (default)
J1: Output reduction

Connect 10P
connector to
XDR port on
rear of
display unit.

Connect 10P
connector to
XDR port on
rear of
display unit.

Содержание SMD7












































Отзывы: