Suzuki GSX1300BK B-King Скачать руководство пользователя страница 190

Страница: 190 / 203

8-4

Waxing the Motorcycle

After washing the motorcycle, waxing and
polishing are recommended to further pro-
tect and beautify the paint.
•

Only use waxes and polishes of good
quality.

•

When using waxes and polishes,
observe the precautions specified by the
manufacturers.

Inspection after Cleaning

For extended life of your motorcycle, lubri-
cate according to “LUBRICATION POINTS”
section.

Follow the procedures in the “INSPECTION
BEFORE RIDING” section to check your
motorcycle for any problems that may have
arisen during your last ride.



WARNING

Wet brakes can cause poor braking per-
formance and may lead to an accident.

Avoid a possible accident by expecting
longer stopping distances after washing
your motorcycle. Apply brakes several
times to let heat dry the brake pads or
shoes.

Содержание GSX1300BK B-King












































































































































































































Результаты поиска

Содержание GSX1300BK B-King

Отзывы:

Suzuki GSX1300BK B-King, Руководство пользователя, Страница: 190 / 203

Результаты поиска

Содержание GSX1300BK B-King

Отзывы: