Suzuki GSX1300BK B-King Скачать руководство пользователя страница 166

Страница: 166 / 203

6-62

Front axle tightening torque:
100 N·m (10.0 kgf-m, 72.5 lb-ft)

Front axle holder bolt
tightening torque:
23 N·m (2.3 kgf-m, 16.5 lb-ft)

Front brake caliper mounting bolt
tightening torque:
39 N·m (3.9 kgf-m, 28.0 lb-ft)

REAR WHEEL REMOVAL



WARNING

Failure to torque bolts and nuts properly
could lead to an accident.

Torque bolts and nuts to the proper
specifications. If you are not sure of the
proper procedure, have your authorized
SUZUKI dealer or a qualified mechanic
do this.



WARNING

A hot muffler can burn you. The muffler
will be hot enough to burn you for some
time after stopping the engine.

Wait until the muffler cools to avoid
burns.

Содержание GSX1300BK B-King












































































































































































































Результаты поиска

Содержание GSX1300BK B-King

Отзывы:

Похожие инструкции для GSX1300BK B-King

Бренды по названию

Популярные бренды

Suzuki GSX1300BK B-King, Руководство пользователя

Результаты поиска

Содержание GSX1300BK B-King

Отзывы:

Похожие инструкции для GSX1300BK B-King

Бренды по названию

Популярные бренды