Suzuki DF40A Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 68

background image

52

NOTE:
To avoid insufficient injection of gear oil, check
the gear oil level 10 minutes after doing the pro-
cedure in the step 4. If the oil level is low, slowly
inject the gear oil up to the correct level.

NOTE:
Recycle or properly dispose of used gear oil.
Do not throw it in the trash, or pour it on the
ground, down a drain, or into the water.



WARNING

Gear oil can cause injury to people or pets.
Repeated, prolonged contact with used gear
oil may cause skin cancer. Even brief contact
with used oil may irritate skin.

• Keep new and used oil away from children

and pets.

• Wear a long-sleeve shirt and waterproof

gloves when handling oil.

• Wash with soap if oil contacts your skin.
• Launder any clothing or rags that are wet

with oil.

NOTICE

If fishing line wraps around the rotating pro-
peller shaft, the propeller shaft oil seal can
become damaged and can allow water to enter
the gear case causing severe damage.

If the gear oil has a milky color, it is contami-
nated with water. Immediately contact your
authorized Suzuki marine dealer for advice.
Do not operate your outboard until the oil is
changed and the cause of the contamination
is corrected.

LUBRICATION

Proper lubrication is important for the safe,
smooth operation and long life of each working
part of your outboard motor. The following chart
shows the lubrication points of your motor and
the recommended lubricant:

LOCATION

LUBRICANT

Throttle/Shift linkage

Marine-grade
water resistant
grease

Propeller shaft

Swivel bracket

Marine-grade
water resistant
grease
(Grease Gun)

Swivel bracket

(DF40AQH/50ATH/60AQH)

Steering bracket

«
...
50
51
52
53
54
...
»

Содержание DF40A





































































Отзывы:

Нет отзывов

Похожие инструкции для DF40A

NF796M-H310 Series

Бренд: JETWAY Страницы: 63

Бренд: Ampro Страницы: 72

1stMainboard VG33

Бренд: FIC Страницы: 38

Бренд: ST Страницы: 11

Бренд: Wintech Страницы: 5

Бренд: J&W Страницы: 40

Бренд: National Semiconductor Страницы: 22

Бренд: Freetech Страницы: 79

Advance 10T Series

Бренд: QDI Страницы: 74

Бренд: Ublox Страницы: 42

Бренд: Unicorn Computer Страницы: 36

Бренд: ASROCK Страницы: 18

Бренд: Biostar Страницы: 115

Бренд: C&T Solution Страницы: 48

Бренд: Gigabyte Страницы: 80

Бренд: Carp Design Страницы: 6

Бренд: DFI Страницы: 48

Бренд: DFI-ITOX Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды