background image

22

INDICATOR

TACHOMETER

TILLER HANDLE MODEL

The tiller handle is equipped with the digital
tachometer/caution indicator.
The engine speed is indicated by the digits on
the tachometer.

NOTE:
The actual engine speed (r/min) is ten times of
the meter display value.

CAUTION SYSTEM

The caution systems are designed to alert you
to certain situations which may cause damage
to your outboard motor.

INDICATOR CHECK

REMOTE CONTROL MODEL

Each time the ignition key is turned to the “ON”
position, four lamps – the REV LIMIT 

1

, the

OIL 

2

, the TEMP 

3

 and the CHECK ENGINE

4

 in the monitor-tachometer will light briefly

and the buzzer will also sound for the first two
seconds, regardless of the motor conditions.

For the next three seconds, the monitor-
tachometer will indicate the total motor operat-
ing hours by means of the lamp flashing and
needle indicating.
After this brief check period, the monitor-
tachometer will return to their stand-by mode
and will only respond to motor conditions
requiring a caution alert.

NOTICE

Your outboard motor may become damaged if
you rely on the Caution System to alert you to
any malfunction that may occur or to give you
an indication of the need for maintenance.

To avoid damage to your outboard motor, reg-
ularly inspect and maintain it.

NOTICE

Continuing to operate your outboard motor
with the Caution System activated can result
in severe damage to your outboard motor.

If the Caution System activates while you are
operating your outboard motor, stop the
motor as soon as possible and correct the
problem or consult your authorized Suzuki
marine dealer for assistance.

Содержание DF40A





































































Отзывы: