Suzuki DF40A Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 68

background image

14

BATTERY INSTALLATION

Secure the battery in a dry area of the boat,
away from vibration.

NOTE:
• It is recommended that the battery be

installed in an enclosed battery case.

• When connecting batteries, hexagon-nuts

must be used to secure battery leads to bat-
tery posts.

To hook up the battery, first connect the red
lead from the motor to the positive battery ter-
minal, then connect the black lead to the nega-
tive battery terminal.

To remove the battery, first disconnect the black
lead from the negative terminal, then discon-
nect the red lead from the positive terminal.

Suzuki recommends that you install the termi-
nal cap on the positive battery terminal to pre-
vent an accidental short circuit of battery
terminals.
If a terminal cap is required, contact your autho-
rized Suzuki marine dealer.

Red lead

Hexagon-
nut

Black
lead

Hexagon-
nut

Hexagon-nut



WARNING

If you place the battery near the fuel tank, a
spark from the battery may ignite the gaso-
line, causing a fire and/or an explosion.

Do not place the fuel tank in the same com-
partment/area as the battery.



WARNING

Batteries produce flammable hydrogen gas
and may explode if they are near flames or
sparks.

Never smoke or cause sparks when working
near the battery. Keep the battery away from
open flames. To avoid creating a spark when
charging the battery, connect the battery
charger cables to the proper terminals before
turning the charger on.



WARNING

Battery acid is poisonous and corrosive. It
can cause severe injury and can damage
painted surfaces.

Avoid contact with eyes, skin, clothing, and
painted surfaces. If battery acid comes in con-
tact with any of these, flush immediately with
large amounts of water. If acid contacts the
eyes or skin, get immediate medical attention.

NOTICE

The electrical system or its components may
be damaged if proper battery precautions are
not followed.

• Be sure to attach battery leads correctly.
• Do not disconnect battery leads from the

battery while the engine is running.

«
...
12
13
14
15
16
...
»

Содержание DF40A





































































Отзывы:

Нет отзывов

Похожие инструкции для DF40A

Бренд: JETWAY Страницы: 46

Бренд: Abit Страницы: 72

Intel P43 Series

Бренд: J&W Страницы: 37

Бренд: MSI Страницы: 91

Бренд: FAAC Страницы: 8

Бренд: Texas Instruments Страницы: 38

Бренд: Xilinx Страницы: 70

Бренд: Alpha Data Страницы: 40

NORA-W10 Series

Бренд: Ublox Страницы: 22

KEMX-1600 Series

Бренд: Quanmax Страницы: 74

H55M-LE - - 01-2010

Бренд: ASROCK Страницы: 181

Supero X9DR3-LN4F+

Бренд: Supermicro Страницы: 113

Бренд: ON Semiconductor Страницы: 8

Бренд: Lucky Star Страницы: 77

Бренд: Gigabyte Страницы: 60

Бренд: Pegatron Страницы: 30

Бренд: Gigabyte Страницы: 96

Бренд: Microchip Technology Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды