Suzuki DF300B Скачать руководство пользователя страница 79

Страница: 79 / 97

7. Check the engine oil level.

NOTE:
To avoid incorrect measurement of engine oil
level, check oil level only when the engine has
cooled.

8. Insert the oil dipstick and turn it 90 degrees

to the right, back to its original position as
shown in the figure.

NOTICE

If the oil dipstick knob is not correctly posi-
tioned when installing the motor cover, the oil
level gauge would be damaged.

When the motor cover is to be attached, make
sure that the oil dipstick knob is positioned as
shown in the figure.

UPPER LIMIT

LOWER LIMIT

9. Reinstall the oil filler cap.

NOTE:
Recycle of properly dispose of used engine oil.
Do not throw it in the trash, pour it on the
ground, down a drain, or into the water.

WARNING

Engine oil can cause injury to people or pets.
Repeated, prolonged contact with used
engine oil may cause skin cancer. Even brief
contact with used oil may irritate skin.

• Keep new and used oil away from children

and pets.

• Wear a long-sleeve shirt and waterproof

gloves when handling oil.

• Wash with soap if oil contacts your skin.
• Launder any clothing or rags that are wet

with oil.

Содержание DF300B


































































































Результаты поиска

Содержание DF300B

Отзывы:

Suzuki DF300B, Руководство пользователя, Страница: 79 / 97

Результаты поиска

Содержание DF300B

Отзывы: