Suzuki DF300B Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 97

Suzuki DF300B Скачать руководство пользователя страница 66

66

OPERATION IN SHALLOW WATER

When  operating  your  boat  in  shallow  water,  it
may be necessary to tilt the motor higher than
the  normal  trim  angle.  When  you  tilt  the  motor
beyond  the  normal  trim  angle,  however,  you
should  only  operate  the  boat  at  slow  speeds.
After returning to deep water, be sure to lower
the motor to the normal trim angle.

To tilt the motor higher than the normal trim
angle, use the Power Trim and Tilt switch.

NOTICE

Improperly securing your boat may cause
damage to your boat or motor, or other prop-
erty damage.

Do not allow your motor to rub against quay
walls, piers or other boats when the boat is
tied up.

8

WARNING

When the motor is beyond the maximum trim
position, the swivel bracket will not have side
support  from  the  clamp  bracket  and  the  tilt
system will be unable to cushion the engine if
the  lower  unit  strikes  an  obstruction.  This
could  lead  to  occupant  injury.  In  addition,
beyond the maximum trim position, the water
intake  holes  may  be  above  the  water  line,
which  can  result  in  severe  engine  damage
from overheating.

Do not operate the engine above 1500 r/min
or operate the boat in a planing attitude with
the engine beyond the maximum trim posi-
tion.

NOTICE

If the motor hits bottom, serious damage can
occur.

Do not allow the motor to hit bottom. If the
motor does strike bottom, inspect it immedi-
ately for damage.

OPERATING THE TROLL MODE

MULTI-FUNCTION GAUGE

Switching to TROLL Mode

Press and hold the [MENU] button during cruis-
ing  operation  at  Trolling  Speed  (minimum
speed),  and  this  will  switch  the  operation  to
TROLL Mode.
For  the  Trolling  Speed,  the  desired  engine
speed  can  be  set  and  maintained  within  the
range  from  600  r/min  to  1200  r/min  using  the
[

] or [

] button.

NOTE:
Please contact your authorized Suzuki Marine
Dealer for more information.

Setting the Troll Mode

1. Shift into forward or reverse gear and make

sure that the throttle is fully closed (in-gear
idle speed).

2. When the [MENU] button is pressed and

held in the Multi-Function Gauge screen, the
confirmation message “Start Troll Mode?” is
displayed.

3. When “YES” is selected:

When  “YES”  is  selected  and  the  [SET]  but-
ton  is  pressed,  one  beep  sounds  to  show
that  it  is  now  in  TROLL  Mode.  At  the  same
time, the screen will change and display the
specific TROLL Mode screen, and
is displayed on the gauge screen. When the
gauge  screen  displays  “Engine  Speed
Screen”  or  “All  Items  Screen”,  the  engine
speed  screen  automatically  changes  from
an analog to a digital display.

«
...
64
65
66
67
68
...
»

Содержание DF300B


































































































Отзывы:

Нет отзывов