manualshive.com logo in svg

Suzuki DF250AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF250AP Скачать руководство пользователя страница 88

88

TROUBLESHOOTING

This  troubleshooting  guide  is  provided  to  help
you find the cause of common complaints.

Starter motor will not operate:

• Emergency  stop  switch  lock  plate  is  not  in

position.

• Starter relay fuse is blown out.
• Sub battery cable fuse is blown out.
• Control handle is not in NEUTRAL.
• Battery  terminal  connection  is  corroded  or

lost.

• Battery power is lost.
• Starter motor is failed.
• If equipped with Keyless Start System:

Engine switch or start/stop switch is failed.
If not equipped with Keyless Start System:
Ignition switch or start/stop switch is failed.

• Electric wiring connection is loose.

Engine will not start (hard to start):

• Fuel tank is empty.
• Fuel is deteriorated.
• Engine starting procedure is mistaken.
• Fuel tank air vent is not opened.
• Fuel  hose  is  not  properly  connected  to

engine.

• Fuel hose is kinked or pinched.
• Fuel filter is clogged.
• Fuel pump is failed.
• Fuel tank filter is clogged.
• Spark plug is fouled.
• Ignition system is fouled.
• Electric wiring connection is loose.

NOTICE

Failure  to  troubleshoot  a  problem  correctly
can  damage  your  outboard  motor.  Improper
repairs  or  adjustments  may  damage  the  out-
board motor instead or fixing it. Such damage
may not be covered under warranty.

If you are not sure about the proper action to
correct a problem, consult your Suzuki marine
dealer.

Engine idles unstably or stalls:

• Spark plug is fouled.
• Fuel hose is kinked or pinched.
• Fuel  hose  is  not  properly  connected  to

engine.

• Fuel is deteriorated.
• Fuel filter is clogged.
• Fuel pump is failed.
• Ignition system is fouled.
• Incorrect engine oil is used.
• Thermostat is failed.
• Electric wiring connection is loose.

Caution system is activated (Caution 
buzzer sounds. Caution LEDs lights.):

• Cooling water passage is clogged.
• Thermostat is failed.
• Water pump is failed.
• Oil change reminder system is activated.
• Engine oil is not enough or deteriorated.
• Engine oil filter is clogged.
• Oil pump is failed.
• Propeller is damaged.
• Battery power is lost.
• Engine control sensor is failed.
• Electric wiring connection is loose.

Shift operation will not be activated:

• Electronic shift control system is failed.

Propeller is not rotated:

• Propeller bush is worn or damaged.
• Drive shaft is damaged.
• Propeller shaft is damaged.

Engine speed will not increase:

• Propeller is damaged.
• Propeller is not clean.
• Propeller is not properly selected.
• Outboard motor is not correctly installed.
• Trim angle is not properly adjusted.
• Spark plug is fouled or incorrectly selected.
• Fuel hose is kinked or pinched.
• Fuel filter is clogged.
• Fuel is deteriorated.
• Fuel pump is failed.
• Ignition system is failed.
• Electronic throttle system is failed.
• Heavy cargo is on the boat.
• Water is entered into the boat.
• Bottom of boat is not clean or damaged.

Содержание DF250AP





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды