manualshive.com logo in svg

Suzuki DF250AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF250AP Скачать руководство пользователя страница 36

36

OIL TEMPERATURE CAUTION SYSTEM

This  system  is  activated  when  the  engine  oil
temperature  is  too  high  due  to  insufficient  oil
cooling or deterioration in quality of engine oil

.

If this system activates, the “High Oil Temp” and
caution  alarm  icon  are  displayed  on  screen,
and  the  buzzer  sounds.  In  addition,  when  this
system  is  activated  at  3000  r/min.  or  higher,
engine  speed  will  automatically  be  reduced  to
approximately 3000 r/min.
If you continue to run, the engine will automati-
cally  stop  3  minutes  after  beginning  of  the
above CAUTION system activation.

NOTE:
In case that the engine is automatically stopped
due to the CAUTION system, the engine can be
started again.
However  the  CAUTION  system  will  repeatedly
activate until eliminating the cause.

The “High Oil Temp” indication clears when any
of the button is pressed in the gauge. However,
the  caution  alarm  icon  is  displayed  until  elimi-
nating the cause.

If  the  oil  temperature  caution  system  activates
when operating, stop the engine immediately, if
wind  and  water  conditions  make  it  to  do  so.
Check the engine oil condition.
If  the  oil  condition  is  fine,  consult  your  autho-
rized Suzuki Marine Dealer.

NOTICE

If  this  system  activates  for  no  apparent  rea-
son, there may be a problem with the system.

Consult your authorized Suzuki marine dealer.

OVERHEAT CAUTION SYSTEM

This system is activated when the cylinder wall
temperature is too high due to insufficient water
cooling.

NOTE:
The  overheat  caution  system  will  not  detect
high  combustion  chamber  temperature  caused
by, for example, an oil system malfunction, poor
quality  fuel,  or  spark  plugs  with  an  incorrect
heat range.

If this system activates, the “Overheat” and cau-
tion  alarm  icon  are  displayed  on  screen,  and
the  buzzer  sounds.  In  addition,  when  this  sys-
tem is activated at 2000 r/min. or higher, engine
speed will automatically be reduced to approxi-
mately 2000 r/min.
If you continue to run, the engine will automati-
cally  stop  3  minutes  after  beginning  of  the
above CAUTION system activation.

NOTE:
In case that the engine is automatically stopped
due to the CAUTION system, the engine can be
started again.
However  the  CAUTION  system  will  repeatedly
activate until eliminating the cause.

The  “Overheat”  indication  clears  when  any  of
the  button  is  pressed  in  the  gauge.  However,
the  caution  alarm  icon  is  displayed  until  elimi-
nating the cause.

If  the  overheat  caution  system  activates  when
operating,  reduce  engine  speed  immediately
and check if water is being discharged from the
pilot  water  hole.  If  no  water  is  seen,  follow  the
procedures outlined below.

Содержание DF250AP





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды