background image

 

16 

Appendix E– Commercial Warranty     

SUTRON MANUFACTURED EQUIPMENT 

THE SUTRON CORPORATION WARRANTS that the equipment manufactured by its manufacturing 
division shall conform to applicable specifications and shall remain free from defects in workmanship and 
material for a period ending two years from the date of shipment from Sutron’s plant. 
  
Sutron’s obligation under this Warranty shall be limited to repair at the factory (22400 Davis Drive, Sterling, 
VA  20164), or at its option, replacement of defective product. In no event shall Sutron be responsible for 
incidental or consequential damages, whether or not foreseeable or whether or not Sutron has knowledge of 
the possibility of such damages. This warranty shall not apply to products that have been damaged through 
negligence, accident, misuse, or acts of nature such as floods, fires, earthquakes, lightning strikes, etc.  
Sutron’s liability, whether in contract or in tort, arising out of warranties or representations, instructions or 
defects from any cause, shall be limited exclusively to repair or replacement parts under the aforesaid 
conditions.  
Sutron requires the return of the defective electronic products or parts to the factory to establish claim under 
this warranty. The customer shall prepay transportation charges to the factory. Sutron shall pay 
transportation for the return of the repaired equipment to the customer when the validity of the damage claim 
has been established. Otherwise, Sutron will prepay shipment and bill the customer. All shipments shall be 
accomplished by best-way surface freight. Sutron shall in no event assume any responsibility for repairs or 
alterations made other than by Sutron. Any products repaired or replaced under this warranty will be 
warranted for the balance of the warranty period or for a period of 90 days from the repair shipment date, 
whichever is greater. Products repaired at cost will be warranted for 90 days from the date of shipment.  
 

NON-SUTRON MANUFACTURED EQUIPMENT 

 
The above Warranty applies only to products manufactured by Sutron. Equipment provided, but not 
manufactured by Sutron, is warranted and will be repaired to the extent of and according to the current terms 
and conditions of the respective equipment manufacturers. 
  

REPAIR AND RETURN POLICY 

 
Sutron maintains a repair department at the factory, 22400 Davis Drive, Sterling, VA 20164. Turn around 
time normally ranges from 10-30 days after Sutron receives equipment for repair. 

Call Customer Service at 

(703) 406-2800 for a Return Material Authorization (RMA) number.

 Return the defective equipment to 

the factory, transportation charges paid. 
  

EXTENDED WARRANTY AND ON-SITE MAINTENANCE 

Extended warranty and on-site maintenance contracts are available. Price quotations may be obtained from 
Sutron customer service representatives. 
 
 
 
 
 
 

Содержание ModbusLink-M



















Отзывы: