background image

Sutron Corporation   8310 & 7310 Users Manual  

8800-1125Rev. 2.7 (BETA)   

12/23/2014  

 

    pg. 

14

 

 
 

 

Compliance Information 

 
The Federal Communication Commission (FCC) has established rules, which permits this device to be directly 
connected to the telephone network. If this device is malfunctioning, it may also be causing harm to the 
telephone network. This device should be disconnected until the source of the problem can be determined and 
until repair has been made. If this is not done, the telephone company may temporarily disconnect service. The 
telephone company may make changes in its technical operations and procedures. If such changes affect the 
compatibility or use of this device, the telephone company is required to give adequate notice of the changes. If 
the telephone company requests information on what equipment is connected to their lines, inform them of the 
following:  
 

a)

 

The telephone number and the device it connected to.  

b)

 

The Ringer Equivalence Number (REN): 0.7B  

c)

 

The device uses an RJ11 type jack.  

d)

 

The FCC Registration Number ~ US: 3A4M507B336SM-T-W  

 
The REN is used to determine the number of devices that may be connected to the telephone line. Excessive 
REN on a telephone line may result in devices not ringing in response to an incoming call. In most, but not all 
areas, the sum of the REN should not exceed five (5.0). To be certain of the number of devices that may be 
connected to a line, as determined by the total REN, contact the telephone company.  
 
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or any 
other electronic device, including fax machines, to send any message unless such message clearly contains in a 
margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and 
time, it is sent and an identification of the business or other entity, or other individual sending the message and 
the telephone number of the sending machine or such business, other entity, or individual. The telephone 
number provided may not be a 900 number or any number for which charges exceed local or long distance 
transmission charges. This equipment must not be used on party lines. Connection to party line service is subject 
to state tariffs. Contact state public utility commission for information. In order to program this information into 
your fax machine or fax / modem, consult your fax machine’s user’s manual for setup instructions.  
 
Industry Canada  CS-03:   IC: 2377A-11813 
This product meets the applicable Industry Canada technical specifications / Le present materiel est conforme 
aux specifications techniques applicables d’Industrie Canada  
 
 
 

Содержание 8080-0005-1B


















Отзывы: