manualshive.com logo in svg

Suspa VariFrame, Руководство по сборке

Поделиться
Скачать
Suspa VariFrame Скачать руководство пользователя страница 5

 

Information concerning this 

document 

 

VariFrame – Assembly Instructions 

 

page 5 

1

 

Information concerning this document 

1.1

 

Structure of the warnings 

The combination of a signal word in conjunction with a pictogram classifies the respective warning. 
The symbol can vary depending on the type of danger. 

 

THE WARNING IS GIVEN BELOW A SIGNAL WORD THAT INDICATES THE 

EXTENT OF THE EXISTING DANGER.  

The first line after the signal word describes the type and source of the potential danger. 

The following section describes the consequences if no measures are adopted to safeguard against 
the danger. 

The last paragraph describes the measures to avoid the danger. 

 

1.2

 

Signal words and signal colors 

The following signal words are based on DIN EN 82079-1 and ANSI Z 535.4, and are used in this 
documentation. The safety colors have been taken from standard  
ISO 3864-1.  

Signal word 

Use 

Explanation 

 

 DANGER  

Warning notice 

Indicates a dangerous situation, which, 

if ignored, leads to death or severe 

injuries. 

 

 WARNING 

 

Warning notice 

Indicates a dangerous situation, which, 

if ignored, may lead to injuries and 

damage to property 

 

 CAUTION 

 

Warning notice 

Indicates a dangerous situation, which, 

if ignored, may lead to minor injuries 

and damage to property 

 IMPORTANT  

Note 

Refers to ways to facilitate and simplify 

operation and cross-references. It 

excludes the danger of damage to 

property and the risk of injuries. 

 SAFETY INSTRUCTION  

Safety instruction 

Draws attention to specific safety-

relevant instructions or procedures.  

Table 1 Signal words and signal colors 

Содержание VariFrame








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды