E N G L I S H •
User's manual
9
IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.
TOOL USE AND CARE
Do not force the power tool. Use the correct tool
for the application. The correct tool will do the
job better and more safely at the rate that it was
designed to work at.
Do not use tools if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect the plug from the power source be-
fore making any adjustments, changing acces-
sories or storing the tool. This preventive safety
measures reduce the risk of accidental starting
of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the op-
eration of the power tool. If it is damaged, have
it repaired before using. Many accidents are
caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in workpieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and differential switch
when you are using an electric equipment.
SERVICE
Tool service must be performed only by qualified
repair personnel. Service or maintenance per-
formed by unqualified personnel could result in
a risk of injury.
SPECIFIC SAFETY RULES FOR
BAND SAWS
1. Always allow the band saw blade to stop be-
fore removing scrap pieces from table.
2. Always keep hands and fingers away from the
blade.
3. Never attempt to saw stock that does not have
a flat surface, unless a suitable support is used.
4. Always hold material firmly and feed it into
the blade at a moderate speed.
5. Always turn off the machine if the material is
to be backed out of an uncompleted out.
6. Adjust the upper guide about “1/8” above the
material being cut.
7. Check for proper blade size and type for thick-
ness and type of material being cut.
8. Make sure that the blade tension and blade
tracking are properly adjusted.
9. Make “relief” cuts before cutting long curves.
10. Release blade tension when the saw will not
be used for a long period of time.
ASSEMBLY & INSTALLATION
IMPORTANT: This machine is shipped partly
disassembled saw table and star knob have to be
installed prior to use.
Unpack machine and check for any visible dam-
age which may have occurred during transport.
If a damage is detected notify your dealer im-
mediately.
INSTALLING TABLE
Install worktable (83) according to figure 1. Fix
the saw mouth (85) into the center of worktable.
Connect the guide board (87) with the table use
four butterfly screw bolts as figure 1. Then make
the square neck bolt (76) plug in the side guide
board through strip-shaper washer (75). Fix the
upper guide board (79) and side guide board
with washer and butterfly nut.
Put the upper board on the right side of saw
blade. Loosen the nuts (77). Take off the upper
guide board and loosen the butterfly nut (76).
Slip the stand of upper guide board (74) to the
SB714 manual.indd 9
28/05/15 10:48