background image

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

4

Introduction

Introducing SureCall’s Force3 PSB Public Safety Band Amplifier. Please read this entire manual be

-

fore proceeding with the installation. This manual applies to the Force3 PSB  model

1.1 - Package Contents

Your BDA box contains the following items: 
• Force3 PSB Bi-Directional Amplifier 
• Mounting kit (not shown).
• DC power supply (not shown).
• Wall anchors (not shown).

1.2 - Features & Benefits

The Force3 PSB BDA offers the following features
and benefits:
• Powerful in-building BDA with 31dB of adjustable gain level.
•  Extends signals in areas with poor coverage due to geographical location 

and/or building design. 

•  Suitable for large areas up to approximately 80,000 square feet depending 

on outside signal strength.

• Power control maintains maximum output power at 3 watts EIRP.
•  Automatic oscillation detection and protection system powers down the BDA 

to prevent harmful radio interference.

1.3 - Additional Items Needed

The Force3 PSB BDA requires the following additonal components for a 
complete installation: 

• External antenna 
• Lightning protector 
• Cable splitter if installing multiple antennas.
• Sufficient SC-400 ultra low loss interior/exterior cable of 50 ohm.
•  Multiple antennas (omnidirectional domes and/or panels by SureCall).
•  Grounded surge suppressor for DC power supply.

Note:

  Due to the recent change of our company name from Cellphone-Mate (CM) to SureCall (SC) we have changed the prefix on all of our 

antennas, cables and accessories from CM to SC-.

Содержание Force3 PSB
























Отзывы: