Superrollo GW70 Скачать руководство пользователя страница 33

Страница: 33 / 40

18. What to do if... ?

Fault

Possible cause / solution

... the superrollo GW70 indicates no functions?

Check the power supply incl. connecting cable and plug.

... the automatic LED flashes?

a) There may have been a power failure. Reconfigure the switching

times, see page 24.

b) After pressing the [

]- or [

Down

] button the automatic LED

lights again permanently.

... the roller shutters no longer stop at the

configured end points?

The end points may be displaced due to elongation of the belt.

Re-adjust the end points, see page 21.

... the automatic LED is rapidly flashing and the

superollo GW70 fails to operate in either

direction?

The maximum running time of the drive has been exceeded,

see page 8 / 11.
The motor is too hot. The belt winder will be fully operational

again in approx. 1 hour.

... the roller shutters stop suddenly during

upward travel?

a) The drive may be jammed, for example, due to the

roller shutters freezing up or other obstacles.

b) The roller shutters may not be running sufficiently smoothly.

Check the roller shutters and roller shutter guides.

c) The roller shutters may be too heavy. The maximum tractive force

of the belt winder has been exceeded.

Содержание GW70









































Результаты поиска

Содержание GW70

Отзывы:

Похожие инструкции для GW70

Бренды по названию

Популярные бренды

Superrollo GW70, Перевод оригинального руководства по эксплуатации и сборке

Результаты поиска

Содержание GW70

Отзывы:

Похожие инструкции для GW70

Бренды по названию

Популярные бренды