Supero X9DRFF-7G+, Руководство пользователя

Страница: 52 / 105

2-28
X9DRFF-iG+/iTG+/7G+/7TG+ Motherboard User’s Manual
LEDS2
HDD_PWR2
T-SGPIO1 T-SGPIO2 6-SGPIO1 6-SGPIO2
VGA1
JPW3
JPW1
FAN8
FAN7 FAN6 FAN5 FAN4 FAN3 FAN2
FAN1
JPI2C1
PWR_SW1
LAN1
I-SA
TA0
I-SA
TA1
L-SAS0 L-SAS2 L-SAS4 L-SAS6
L-SAS1 L-SAS3 L-SAS7
L-SAS5
UID_LED1
FAILURE_LED1
USB1
I-SA
TA2 I-SA
TA3 I-SA
TA4 I-SA
TA5
JIPMB1
JPB1
JPL1
JPME1
JPME2
JWD1
JPG1
JBR1
1
JP6
JP7
CPLD1
JBT1
HDD_ACT_LED1
JI2C2
JI2C1
JBAT1
BIOS
PCH SLOT4 PCIE-E 2.0X4 CPU1 SLOT3 PCI-E 3.0X8 CPU1 SLOT2 PCI-E 3.0X8
CPU1 SLOT1 PCI-E X16 PROPRIET
AR
Y SLOT
P2-DIMMH2
P2-DIMMH1
P2-DIMMG2 P2-DIMMG1
P1-DIMMA1
P1-DIMMD1
P1-DIMMA2
P1-DIMMD2
P1-DIMMB1
P2-DIMME1
P1-DIMMB2
P2-DIMME2
P1-DIMMC1
P2-DIMMF1
P1-DIMMC2
P2-DIMMF2
JSD1
SXB1:CPU2 PCI-E X32 PROPRIENT
AR SLOT
PS_ON_N
HDD
UID_SW1
USB0
LAN2
IPMI_ LAN
USB2
JPW2
PWR1
Rev. 1.01
X9DRFF-iG+
BMC_HB_LED1
BMC
Intel LAN
CTRL
LSI SAS
CTRL
Intel PCH
Rear_FAN
IPMI CODE
MAC CODE
SAS CODE
MEGERAC LICENSE
JPS1
CLOSE 1st
OPEN 1st
CPU2
CLOSE 1st
OPEN 1st
CPU1
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connection.
Always remove the AC power cord from the system before clearing CMOS.
Note 1:
For an ATX power supply, you must completely shut down the
system, remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2: Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3: Clearing CMOS will also clear all passwords.
A
B
A. Clear CMOS
B. Watch Dog Enable
Watch Dog Enable/Disable
Watch Dog (JWD1) is a system monitor that will re-
boot the system when a software application hangs.
Close pins 1-2 to reset the system if an application
hangs. Close pins 2-3 to generate a non-maskable
interrupt signal for the application that hangs. See
the table on the right for jumper settings. Watch Dog
must also be enabled in the BIOS.
Watch Dog
Jumper Settings
Jumper Setting Definition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled