Chapter 2: Installation
2-31
DM1
JPG1
JBT1
J21
JTPM1
JIPMB1
FANB
FAN4
FAN2
FAN1
JI2C1
JI2C2
JBAT1
JSD1
J22
JPW2
JPI2C1
JD1
JF1
X9DR7/E-LN4F
Rev. 1.00
CPU2 SLOT3 PCI-E 3.0 X16
L-SAS 4~7
CPU2 SLOT4 PCI-E 3.0 X8
CPU1 SLOT1 PCI-E 3.0 X8
XDP-CPU
CPU1 SLOT2 PCI-E 3.0 X8
I-SA
TA0
COM2
USB4/5
S-SA
TA2
S-SA
TA0
CPU1 SLOT6 PCI-E 3.0 X8
CPU2 SLOT5 PCI-E 3.0 X16
L-SAS 0~3
P1 DIMMC1
P1 DIMMC2
P1 DIMMD1
P1 DIMMD2
P1 DIMMB2
P1 DIMMB1
P2 DIMME1 P2 DIMME2
P1 DIMMA2
P2 DIMMF1
P1 DIMMA1
P2 DIMMF2
P2 DIMMH2
P2 DIMMH1
P2 DIMMG1
P2 DIMMG2
JPWR1
LE1
T-SGPIO2
CPU2
CPU1
BMC
CTRL
CTRL
LAN
PCH
CTRL
SAS
SP1
FAN3
FANA
JF2
JOH1
JWD
JSTBY1
JS7
JS6
JL1
JS6
JS5
S-SA
TA1
S-SA
TA3
T-SGPIO1
I-SA
TA3
I-SA
TA2
I-SA
TA1
I-SA
TA4
I-SA
TA5
BIOS
SCU-SGPIO1
USB6
J23
J25
JPB1
J30
J29
JPL1
FAN5
Battery
JPWR2
LAN2/4
LAN1/3
USB2&3
USB0&1
IPMI_LAN
KB/Mouse
COM1
VGA
FAN6
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connection.
Always remove the AC power cord from the system before clearing CMOS.
Note 1.
For an ATX power supply, you must completely shut down the sys-
tem, remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2.
Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3.
Clearing CMOS will also clear all passwords.
A
B
A. Clear CMOS
B. Watch Dog Enable
Watch Dog Enable/Disable
Watch Dog (JWD) is a system monitor that
will reboot the system when a software ap-
plication hangs. Close Pins 1-2 to reset the
system if an application hangs. Close Pins
2-3 to generate a non-maskable interrupt
signal for the application that hangs. See the
table on the right for jumper settings. Watch
Dog must also be enabled in the BIOS.
Watch Dog
Jumper Settings
Jumper Setting Definition
Pins 1-2
Reset (default)
Pins 2-3
NMI
Open
Disabled
