Supero SuperWorkstation 5038AD-T Скачать руководство пользователя страница 72

Страница: 72 / 130

6-4

uper

orkstation 5038AD-T User's Manual

6-3 Removing and Installing Hard Drives

Internal 3.5" Hard Drives

The SC732G chassis features hot-swappable internal hard drives. It is not neces-

sary to power down the system before removing and reinstalling the internal 3.5"

hard drives.

Removing and Installing 3.5" Hard Drives

1. Without powering down the system, remove the cover as described in Section

6-2.

2. Press the release tab on the side of the hard drive carrier that is to be re-

moved from the hard drive cage.

3. Pull the hard drive carrier out of the hard drive cage by the drive carrier

handle.

Figure 6-3. Removing a Hard Drive Carrier from the Hard Drive Cage

Release Tabs

Содержание SuperWorkstation 5038AD-T



































































































































Результаты поиска

Содержание SuperWorkstation 5038AD-T

Отзывы:

Похожие инструкции для SuperWorkstation 5038AD-T

Бренды по названию

Популярные бренды

Supero SuperWorkstation 5038AD-T, Руководство пользователя

Результаты поиска

Содержание SuperWorkstation 5038AD-T

Отзывы:

Похожие инструкции для SuperWorkstation 5038AD-T

Бренды по названию

Популярные бренды